2012 {{URL}}

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2012
XC60 (-17) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
13199081.331414412, 31414411, 31414409, 31414408, 31414407, 31414405, 31414404, 31414403, 31414402, 31414401, 31414400, 31414399, 31414398, 31399403, 31399402, 31399401, 31399399, 31399105, 31399104, 31399103, 31373300, 31373296, 31414410, 1319749, 1319748, 1319747, 1319746, 1319738, 1319737, 1319736, 1319735, 1319734
Multimedia system, RSE, two screens, with two players, (Ch 175379-)




Equipment
IMG-242205
IMG-345497
IMG-239664

IMG-382145

IMG-382146


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-329148
 

2
IMG-329149
 

3
IMG-329150
 

4
IMG-303004
 

  • Tightening torque screws: 40 Nm (29.5 lbf.ft.).

5
IMG-303005
 

6
IMG-303006
 

  • Tightening torque screws: 40 Nm (29.5 lbf.ft.).

    Repeat the method steps for the other seat.

7
IMG-332179
 

  • Set the ignition key to position 0.

  • Disconnect the battery negative lead.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.



Note!

The SRS system remains active for a brief period after power is disconnected. Thus, wait three minutes before starting work.


8
IMG-329151
 

9
IMG-329209
 

  • Loosen the connector by unscrewing the screw.

10
IMG-329152
 

Applies to cars without seat belt tensioners in seats

11
IMG-330333
 

Applies to cars with seat belt tensioner in seat

12
IMG-330334
 

Applies to cars with seat belt tensioner in seat

13
IMG-329153
 

Applies to all models

  • Lift out seat.

  • Repeat the method steps for the other seat.

14
IMG-292826
 

15
IMG-292804
 

16
IMG-344796
 

17
IMG-344818
 

  • Use tape to protect the tunnel console.

18
IMG-293021
 

19
IMG-293022
 

20
IMG-293023
 

21
IMG-293024
 

22
IMG-293025
 

23
IMG-293026
 

24
IMG-329163
 

25
IMG-293028
 

26
IMG-293029
 

  • Remove the panel.

27
IMG-329164
 

  • Remove the screws.

28
IMG-344819
 

  • Unplug the connector.

29
IMG-344825
 

30
IMG-344827
 

31
IMG-344828
 

  • Secure the connectors with butyl tape.

32
IMG-329435
 

33
IMG-329164
 

  • Reinstall the removed part.

  • Ensure that no part of the cable harness is trapped.

34
IMG-330503
 

  • Secure the cable marked "Passenger side/RH" with a cable tie.

35
IMG-330504
 

36
IMG-344830
 

37
IMG-344831
 

  • Position the control module where the image shows.

38
IMG-344832
 

  • Position the excess where the image shows.

39
IMG-329448
 

  • Route the cable marked "Driver side/LH" between air duct and climate unit over to the left side.

40
IMG-344833
 

  • Position the cable harness as illustrated.

41
IMG-340508
 

42
IMG-344834
 

43
IMG-344835
 

44
IMG-344836
 

45
IMG-344837
 

46
IMG-330574
 

  • Secure the cable marked "Driver side/LH" with a cable tie.

47
IMG-344841
 

48
IMG-344843
 

  • Cut off foam tape excess.

49
IMG-344844
 

  • Route the cable marked "Passenger side/RH" between air duct and climate unit over to the right-hand side.

50
IMG-344845
 

  • Position the cable harness.

51
IMG-344846
 

52
IMG-330705
 

  • Secure the 2 cables at the existing cable harness using a cable tie.

53
IMG-344847
 

54
IMG-330708
 

  • Secure the 2 cables at the existing cable harness using a cable tie.

55
IMG-330708
 

  • Fasten the 2 cables to the harness in the seat's cable harness with a cable tie.

56
IMG-268413
 

  • Remove the knob for the lumbar support adjustment by removing the cover using a small screwdriver and pull the knob straight off.

57
IMG-337621
 

  • Take a long cable tie and thread it from the hole for lumbar adjustment and up to the hole for the head restraint's inner mounting. The cable tie must be routed between the upholstery and the protection.

58
IMG-337624
 

  • Position the head restraint as illustrated.

59
IMG-338008
 

Applies when installing on the left-hand seat

  • Pull the zip fastener forward.

60
IMG-338009
 

  • Open the zip fastener.

61
IMG-344888
 

  • Transfer the cables to the opposite side.

62
IMG-344887
 

  • Close the zip fastener.

  • Fold the excess back.

63
IMG-337627
 

Applies to all models

  • Tape the cables to the cable tie.

64
IMG-337623
 

  • Place the head restraint in the seat.


Note!

The cables must be in front of the head restraint tube.


65
IMG-337625
 

  • Push the head restraint in to place at the same time as feeding the cables forward.

66
IMG-344851
 


Caution!

Check that the head restraint has locked into place by pulling it upwards.


67
IMG-262956
 

  • Using your fingers, press the cables under the protection. The cables must not press out the upholstery after installation.

    Padding (1)

    Protective pad (2)


Note!

The image shows a seat without upholstery.


68
IMG-337622
 

  • Pull the cable tie with cables through the hole and out at the lower edge.

  • Remove the cable tie and tape from the cable harness.

69
IMG-344892
 

  • Pull the cables forward and in under the seat. Follow the existing cable.

  • Secure the cables using three cable ties

  • Reinstall the lumbar adjustment.


Note!

The image shows a seat without upholstery.


70
IMG-329473
 

  • Place the seat in the vehicle.

71
IMG-344852
 

  • Connect the 2-pin connector.

72
IMG-330728
 

  • Connect the green connector.

  • The groove and the arrow should stand directly opposite each other.

73
IMG-330729
 

  • Connect the black connector.

  • The grooves should be opposite each other.

74
IMG-330730
 

  • Install the connector casings.

75
IMG-330731
 

  • Install cable ties around the connector casings.

76
IMG-329270
 

77
IMG-329268
 

78
IMG-329269
 

  • Repeat the method steps for the other seat.

  • Reinstall the detached components in reverse order.

79
IMG-336901
 

  • Reconnect the negative lead.

80
IMG-336904
 


Warning!

When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.


  • Set the ignition switch to position II.

81
IMG-275777
 

  • Install the batteries in the remote control and headsets.

  • Region code the DVD players. Information is available under:

    • Product specifications

    Design and Function

    3 Electrical system

    39 Media - communication and entertainment

    393 Equipment for entertainment

    Rear seat entertainment system

    Design

  • Place remote controls, headsets, wiring and quick-guide in a suitable place in the vehicle.

© Volvo Car CorporationMultimedia system, RSE, two screens, with two players, (Ch 175379-)- 1319908 - V1.3
volvocars.com
Lifestyle Collection
Deutsch
Find a Dealer
Switzerland

Cookies Legal Disclaimer Privacy Policy Copyright

Copyright © 2024 Volvo Cars. All rights reserved.