Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

When installing, the car must retain a temperature of 20 degrees C.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Preparation

Vehicles with folding towbar, hitch

Press the button.

Fold out the towbar.

Remove the screws.

The part is not to be reused.

Fold marked part aside.

Install component that comes with the accessory kit.

Install components that come with the accessory kit.

Tighten the bolts.

Fold in the towbar.

Vehicles with Foot movement detection (FMDM)

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31470436

Clean the Bumper Cover surface.

Accessory installation

Fold the protective film forward

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Press the marked component.

Remove the protective film.

Drill one hole and fit one pop rivet at a time, in accordance with the sequence illustrated.

Install component that comes with the accessory kit.

Ensure that all clips engage.

Drill one hole and fit one pop rivet at a time, in accordance with the sequence illustrated.

Concerns rear Skidplate

Removal

Vehicles without Integrated Exhaust End Pipes

Vehicle without actuator

Measure and mark as illustrated.

Remove the marked part.

Use special tool: T1158590, PIPE CUTTER

Vehicles with actuator, early version

Measure and mark as illustrated.

Remove the marked part.

Use special tool: T1158590, PIPE CUTTER

Loosen the clip.

Disconnect the connector.

Loosen the nut.

Remove the marked part.

Remove the marked part.

The part is to be reused.

Remove the nuts.

Remove the marked part.

The part is to be reused.

Vehicles with actuator, late version

Loosen the clip.

Disconnect the connector.

Measure and mark as illustrated.

Remove the marked part.

Use special tool: T1158590, PIPE CUTTER

Remove the nuts.

Remove the marked part.

The part is to be reused.

All vehicles

Remove the screws.

The part is to be reused.

Release the catches.

Remove the marked part.

Vehicles with Foot movement detection (FMDM)

Request the aid of a colleague for this procedure.

Release the catches.

Loosen the component indicated. Do not remove it.

Disconnect the connector.

Remove the fasteners.

Remove the marked part.

Remove the screws.

Release the catches.

Remove the marked part.

1. Release the lock.

2. Release the connector's catch.

Disconnect the connectors.

Release the catch.

Remove the marked part.

Remove the screws.

Fold the wing liner aside.

Remove the screw.

Loosen the component indicated. Do not remove it.

Accessory installation

Release the catches.

Remove the marked part.

The part is not to be reused.

Remove the marked part.

Use: Air-powered air saw

Install component that comes with the accessory kit.

Check that the component has locked in its position.

Vehicles with Foot movement detection (FMDM)

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Apply a thin layer of primer.

Use: 1161765, Primer

Allow to dry for at least 10 minutes.

Install the marked component.

Install components that come with the accessory kit.

Note position of components.

Remove the protective film.

Install components that come with the accessory kit.

1. Loosen the clip.

   Remove the clip.

2. Remove the tape.

   Remove the clips.

3. Remove the clip.

Vehicles without Parking assistance pilot

Position/route the cables as illustrated.

Install components that come with the accessory kit.

Connect the connector.

Position the cable harness excess as illustrated.

Install component that comes with the accessory kit.

Vehicles with Parking assistance pilot

Position/route the cable as illustrated.

Install components that come with the accessory kit.

Connect the connector.

Position the cable harness excess as illustrated.

Reinstall the removed part.

Ensure that all clips engage.

Reinstall the screw.

Reinstall the screws.

All vehicles

Install component that comes with the accessory kit.

Ensure that all clips engage.

Reinstall the screws.

Vehicles without Integrated Exhaust End Pipes

Install component that comes with the accessory kit.

Tighten to the value stated.

Tightening torque: M10 , 50 Nm

Vehicle without actuator

Install component that comes with the accessory kit.

Tighten to the value stated.

Tightening torque: M10 , 50 Nm

Vehicles with actuator, early version

Reinstall the removed part.

Tightening torque: Actuator, to Exhaust system , 5 Nm

Reinstall the removed part.

Tighten the nuts.

Install component that comes with the accessory kit.

Tightening torque: ,

Tighten to the value stated.

Connect the connector.

Install the clip(s).

Vehicles with actuator, late version

Tightening torque: Actuator, to Exhaust system , 5 Nm

Reinstall the removed part.

Tighten the nuts.

Install component that comes with the accessory kit.

Tightening torque: M10 , 50 Nm

Tighten to the value stated.

Connect the connector.

Install the clip(s).

Vehicles with Foot movement detection (FMDM)

Check

Check for correct operation.