Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Open the hood.

Remove the marked detail/details.

Use: Pliers 31423632

Remove the screws.

Remove the marked part.

Remove the clips.

Remove the screws.

Remove the nut.

Remove the screws.

Remove the nut.

Remove the clip.

Remove the marked part.

Remove the clips.

Remove the screws.

Remove the clips.

Remove the cable harness clips.

Loosen the screws.

Remove the marked part.

Fold marked part aside.

Remove the screws.

Remove the marked part.

Remove the screw.

Release the catches.

Loosen the marked detail.

Accessory installation

Measure and mark out the centre.

Use a drill with the stated size

Assemble components that come with the accessory kit.

Pull the wiring through.

Install component that comes with the accessory kit.

This is used as a counterhold.

Install components that come with the accessory kit.

Tighten the nut.

Use hands only.

Reinstall the removed part.

Reinstall the screw.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Ground connection

Release the catches.

Loosen the marked detail.

Remove the nut.

Position/route the cable as illustrated.

Connect the prerouted cable.

Install the marked component.

Ensure that all clips engage.

Install the nut.

Tightening torque: M6 , 10 Nm

Installation

Reinstall the removed part.

Reinstall the screws.

Reinstall the removed part.

Reinstall the removed part.

Reinstall the screws.

Reinstall the removed part.

Accessory installation

Lubricate the O-ring.

Use: 1161427, Low temperature grease

1. Cable from front socket

2. Engine heater cable

Connect the cable.

Install the catch.

Place the cable tie as illustrated.

Position/route the cable as illustrated.

Install the cables.

Place the cable tie as illustrated.

Position/route the cable as illustrated.

Tighten the cable tie.

Install a clips onto the upper edge of the subframe.

Install the cable.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

1. Steering gear

2. Cable harness

3. Engine heater cable

Position/route the cable as illustrated.

Install the cable.

Remove the screws.

Clean the surface.

Install components that come with the accessory kit.

Tighten the screw.

Remove the protective film.

Install component that comes with the accessory kit.

Press the marked component.

Install components that come with the accessory kit.

Tighten the screw.

Lubricate the O-ring.

Use: 1161427, Low temperature grease

Connect the cable.

Install the catch.

Fasten the cable tie without tightening.

Adjust the cable position so that it can follow the motions of the engine.

Tighten the cable tie.

Tighten the cable ties.

Installation

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm