| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-400007 |
|
| | Note!
If a pending accessories installation include the removing and replacing of the bumper, this installation should be carried out first. |
When installing, the car must retain a temperature of 20 degrees C. After installation, the car must not be washed for 48 hours |
| | |
|  | | IMG-363036 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | Applies to unpainted component |
|  | | IMG-403830 |
|
| | |
| | Vehicles with Parking assistance pilot |
|  | | IMG-407652 |
|
| | Print templates from Service Product Journal (SPJ) 30519 |
|  | | IMG-407831 |
|
| | Secure the template with tape. Scribe/mark up Remove the tape.
Repeat on the other side. |
|  | | IMG-407851 |
|
| | Secure the template with tape. Scribe/mark up Remove the tape.
Repeat on the other side. |
| | |
| | |
|  | | IMG-382894 |
|
| | Note!
The screws are to be reused. |
Remove the screws. |
|  | | IMG-382895 |
|
| | Note!
The screws are to be reused. |
Remove the screws. |
|  | | IMG-393050 |
|
| | Remove the marked part. The part is not to be reused. |
|  | | IMG-393051 |
|
| | Remove the marked part. The part is not to be reused. |
|  | | IMG-393060 |
|
| | |
|  | | IMG-393062 |
|
| | |
|  | | IMG-382898 |
|
| | |
|  | | IMG-382932 |
|
| | Remove the marked part. The part is not to be reused. |
|  | | IMG-400990 |
|
| | Caution!
Cut carefully to avoid unintentional damage or personal injury. |
Locate relevant marking. |
|  | | IMG-382998 |
|
| | Caution!
The part is to be reused. |
Remove the weatherstrip. |
|  | | IMG-408475 |
|
| | Note!
Make sure that the mating faces are clean and free of foreign material. |
Remove the marked part.
Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | Vehicles with Parking assistance pilot |
|  | | IMG-383588 |
|
| | Remove the screws. Remove the marked part. |
|  | | IMG-383613 |
|
| | Fold the wing liner aside. Disconnect the connector. Remove the part carefully The part is to be reused. |
|  | | IMG-383638 |
|
| | |
|  | | IMG-407875 |
|
| | Remove the marked part. Use: Air-powered air saw
|
|  | | IMG-393176 |
|
| | |
|  | | IMG-401258 |
|
| | Release the catches. Remove the part carefully |
|  | | IMG-393178 |
|
| | |
|  | | IMG-383440 |
|
| | Disconnect the connector. Remove the marked part. |
|  | | IMG-393180 |
|
| | |
|  | | IMG-407926 |
|
| | Remove the marked part. Use: Air-powered air saw
|
| | |
|  | | IMG-383483 |
|
| | Locate the connector. Pull the wiring through. |
|  | | IMG-393179 |
|
| | |
|  | | IMG-393177 |
|
| | |
| | |
| | |
|  | | IMG-383287 |
|
| | Reinstall the weatherstrip. |
|  | | IMG-393630 |
|
| | |
|  | | IMG-393634 |
|
| | |
|  | | IMG-383292 |
|
| | Caution!
Make sure not to damage painted surfaces. |
Note!
This step is easier with two people. |
Install component that comes with the accessory kit. Use hands only. |
|  | | IMG-411835 |
|
| | |
|  | | IMG-393275 |
|
| | Install component that comes with the accessory kit. Install the clips as illustrated. |
|  | | IMG-394588 |
|
| | Clean the surfaces. Use: 1161721, Cleaning agent
|
|  | | IMG-394598 |
|
| | Clean the surfaces. Use: 1161721, Cleaning agent
|
|  | | IMG-397767 |
|
| | Clean the surface. Use: 1161721, Cleaning agent
|
|  | | IMG-425420 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425422 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425426 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425448 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425450 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425466 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425467 |
|
| | Note!
This step is easier with two people. |
Hold the component in the position shown. Use: Masking tape
Remove the marked part. |
|  | | IMG-425290 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-425292 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-425485 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-425486 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-425296 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
|
|  | | IMG-425294 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-425297 |
|
| | Apply a thin layer of primer. Allow to dry for at least 5 minutes but not more than 30 minutes. Use: 1161727, Primer
Remove the tape. |
|  | | IMG-393283 |
|
| | Remove the protective film. Fold the protective film forward
|
|  | | IMG-393310 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-393286 |
|
| | Install component that comes with the accessory kit. Install the clip(s). Remove the protective film. Fold the protective film forward
|
|  | | IMG-400452 |
|
| | Ensure that all clips engage. |
|  | | IMG-400362 |
|
| | Note!
Adjust the position of the components to create even spaces. |
|
|  | | IMG-393285 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
|  | | IMG-397752 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
| | Vehicles with Parking assistance pilot |
|  | | IMG-383720 |
|
| | Locate the pre-routed connector. Reinstall the removed part. Connect the connector.
|
|  | | IMG-383721 |
|
| | Reinstall the removed part. Reinstall the screws. |
| | |
|  | | IMG-393287 |
|
| | Install component that comes with the accessory kit. Install the clip(s). Remove the protective film. Fold the protective film forward
|
|  | | IMG-393294 |
|
| | Ensure that all clips engage. |
|  | | IMG-393290 |
|
| | Install component that comes with the accessory kit. Install the clip(s). Remove the protective film. Fold the protective film forward
|
|  | | IMG-393297 |
|
| | Ensure that all clips engage. |
|  | | IMG-400995 |
|
| | Note!
Adjust the position of the components to create even spaces. |
Adjust the component to a horizontal position. |
|  | | IMG-400999 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
|  | | IMG-401000 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
|  | | IMG-393284 |
|
| | Install component that comes with the accessory kit. Install the clips as illustrated. |
| | Vehicles with Parking assistance pilot |
|  | | IMG-393299 |
|
| | Reinstall the removed part. |
|  | | IMG-393301 |
|
| | |
| | |
|  | | IMG-393295 |
|
| | Install component that comes with the accessory kit. Remove the protective film. Fold the protective film forward
|
|  | | IMG-393296 |
|
| | |
|  | | IMG-393190 |
|
| | |
|  | | IMG-393292 |
|
| | Install component that comes with the accessory kit. Install the clip(s). Remove the protective film. Fold the protective film forward
|
|  | | IMG-400451 |
|
| | Ensure that all clips engage. |
|  | | IMG-393192 |
|
| | |
|  | | IMG-393293 |
|
| | Fold the protective film forward |
|  | | IMG-400356 |
|
| | Note!
Adjust the position of the components to create even spaces. |
|
|  | | IMG-400627 |
|
| | Note!
Adjust the position of the components to create even spaces. |
|
|  | | IMG-383384 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
|
|  | | IMG-393298 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
|  | | IMG-397760 |
|
| | Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film. Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
Hint
To ease removal of the protective film, use interior trim remover tool to lift the component just a bit. |
|
| | Applies to unpainted component |
|  | | IMG-403845 |
|
| | Apply a thin and even layer. |
|  | | IMG-403848 |
|
| | Apply a thin and even layer. |
|  | | IMG-403855 |
|
| | Fold the protective film forward |
|  | | IMG-403909 |
|
| | Install component that comes with the accessory kit. Use: Pop rivet pliers
|
|  | | IMG-404255 |
|
| | Caution!
Make sure that equal pressure is applied to the full length of the component. |
Note!
Apply a pressure of 35 - 50 N/cm2 for 2-3 seconds. This corresponds to a thumb pressure of 3.5 - 5 kg - test with scales first. If the palm of a hand or an application roller is used, remember that the larger surface requires greater force. |
Remove the protective film.
Hint
Press and apply pressure to the part over the tape for at least 20 seconds. |
|
|  | | IMG-400487 |
|
| | Caution!
Make sure that the surface is clean and free of foreign material. |
Wax the component indicated. |
|  | | IMG-377070 |
|
| | Repeat all method steps for the other side. |
