2010 L.H.D

Pokyny pro instalaci

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2010
XC60 (-17) 2010

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307563191.231201135, 30756314
Parking assistance, camera, rear, (Ch -175378)




IMG-302783




Equipment
IMG-242205
IMG-345497
IMG-239664
IMG-239660
IMG-239981
IMG-326754
IMG-326756
IMG-326757
IMG-352231

IMG-328933

IMG-302785

IMG-328934


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

Some steps in these installation instructions are presented with illustration only.


 
1
IMG-332193
 

Applies to all models

  • Set the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


2
IMG-291603
 

3
IMG-291604
 

4
IMG-303067
 

  • Remove the screw at the lower edge of the boot lid's upper panel. Perform on both sides.

5A
IMG-302788
5B
IMG-302789
 

Illustrations A and B

  • Detach the panel's lower, outer and inner ends from the lower panel, and pull it from the clip at the sides.

  • Repeat the operation on the other side.

6
IMG-302790
 

  • Detach the boot lid's upper panel at the upper edge by using a weatherstrip tool until the clips release.

  • Place the panel to one side.

7
IMG-302983
 

  • Remove the panel for the boot lid's lock.

8
IMG-303807
 

  • Remove the two screws from the opening handle.

9A
IMG-302984
9B
IMG-302985
 

Illustrations A and B

  • Carefully pry off the lighting, detach the connector and place to one side.

10A
IMG-302986
10B
IMG-302987
 

Applies to cars with electric boot lid opener

Illustrations A and B

  • Carefully pry off the connector from the panel using a weatherstrip tool.

  • Unplug the connector from the contact and place to one side.

11A
IMG-329745
11B
IMG-329746
 

Applies to all models

Illustrations A and B

  • Remove the lower panel by first prying loose the four clips at the bottom.

  • Then pull the panel off carefully, insert a pair of flat-nosed pliers, press the locking pin's hooks together and pull the locking pin out.

  • Continue to pull the panel down carefully until the four upper clips release.

12A
IMG-303043
12B
IMG-303064
 

Illustrations A and B

  • Remove the six nuts securing the handle.

13A
IMG-303065
13B
IMG-303066
 

Illustration A

  • Carefully pry off the handle from the boot lid using a weatherstrip tool. It is secured by twelve catches.

Illustration B

  • Disconnect the connector and place the handle to one side. New handle can be found in the kit.

14
IMG-281472
 

  • Carefully pry off the rear roof panel at the rear edge until the clip on the inside releases and then pull backward. Place the panel to one side.


Note!

The roof panel is securely fastened.


15
IMG-303068
 

  • Remove the upper part of the side panel.

16
IMG-303069
 

  • Slacken off the two screws that hold the boot lid's sill at the crossmember a few turns.

  • Carefully pull off the trunk lid's sill panel. The panel is secured by six clips.

17
IMG-328943
 

  • Remove the seat cushion by pushing in the sprung lock (1) underneath and then pulling upward (2).

  • Repeat the operation on the other side.

18
IMG-328944
 

Applies to cars with electrically heated seat cushions

  • Disconnect the connectors by the sides at the rear edge of the seat cushion.

19
IMG-268017
 

20
IMG-268018
 

  • Fold the left-hand backrest forward.

  • Remove the side cushion on the left by first pulling it backwards at the upper edge until the hooks (1) release. Then pull it inwards slightly until the hook (2) releases, and upwards until the locating pin (3) disengages from the mounting at the rear edge.

21
IMG-303083
 

22
IMG-303084
 

23
IMG-303085
 

  • Remove the C-pillar panel by carefully pulling it out at the lower edge so that the two retaining clips release.

  • Pull it out at the upper edge until the last clip releases.

  • Carefully unhook it from the roof panel.

24
IMG-303104
 

  • Take the angled end of a scriber and pull off the cover washers for the screws for the load securing eyelets.

  • Remove the screws for the load securing eyelets and the screws at the front edge of the side panel.

25A
IMG-303144
25B
IMG-303145
 

Illustrations A and B

  • Remove the left-hand side panel by grasping it at the upper edge and carefully pulling it from the car body. Lift up the panel and pull it to one side. The panel is secured by six clips.

26
IMG-328958
 

  • Take the camera, new handle and screws from the kit.

  • Tighten the camera to the handle.

27
IMG-330068
 

  • Take the cable harness marked A from the kit and insert the cable in the large hole in the panel and out through the hole where the handle was.

28
IMG-328959
 

  • Pull the cable harness through the right-hand hole in the boot lid.

  • Connect the cable harness connector to the camera. Ensure that the catch engaged again properly.

29A
IMG-328960
29B
IMG-303170
29C
IMG-303171
 

Illustrations A, B and C

  • Insert the connector with camera into the hole on the right side of the boot lid.

  • Connect the connector on the left-hand side and press the handle into place.

30A
IMG-303172
30B
IMG-303173
 

Illustrations A and B

  • Tighten the handle with existing screws.

31
IMG-303174
 

  • Route the cable along the existing cable to the heating elements in the rear window towards the right-hand side of the boot lid.

  • Route it along the right-hand side of the boot lid window up to the upper edge of it.

  • clamp it using a cable tie from the kit and pieces of butyl tape.

32
IMG-303175
 

  • Drill two Ø 6.5 mm (17/64 ") holes for clamping the cable at the upper edge of the boot lid, in the positions illustrated.

  • Remove any swarf.

33
IMG-303176
 

  • Press two cable ties with clips into the drilled holes.

  • Press the cable into a piece of butyl tape above the right-hand hole for the panel's clips so that it does not get trapped when the panel is reinstalled.

  • Tighten the cable with the clamps.

34
IMG-303177
 

  • Carefully pry off the left-hand side of the rubber grommet so that the catches release.

  • Unhook the rubber grommet from the boot lid.

  • Carry out the same with the end that is in the body.

35
IMG-303178
 

  • Insert the cable through the hole in the boot lid and out through the hole in which the rubber grommet was located.


Note!

Reinforcements are located on the inside upper edge of the boot lid which can become blocked. Therefore, first insert the cable slightly to the left before inserting downwards.


36
IMG-303265
 

  • Clamp the cable at the hole edge using a cable tie with edge clips.

37
IMG-303266
 

  • Insert the piece of wire through the boot lid's rubber grommet.

  • Tape the connector and a piece of the cable at the wire.

  • Lubricate the taped connector with low temperature grease.


Note!

The low temperature grease must not contain water.


  • Remove the tape and wire spring.

38
IMG-303267
 

  • Insert the cable through the hole in the body.

39A
IMG-328963
39B
IMG-328964
 

Illustrations A and B

  • Take the receptacle housing with catch for the camera cable's contact from the kit.

  • Press the receptacle housing onto the connector until a click is heard.

  • Press the catch securely into the receptacle housing.


Note!

The components are small and fragile, so take care when aligning the connector and receptacle housing with catch into each other to avoid damage and resulting poor contact.


40
IMG-303283
 

  • Reinstall the rubber grommet in the body and boot lid.

41A
IMG-303284
41B
IMG-328965
 

Illustrations A and B

  • Route the cable harness to the left towards the D pillar.

  • Route at the D pillar along the existing cable harness to the rear edge of the fuse holder.

  • Secure it using seven cable ties along the existing cable harness.


Note!

Ensure that the cable does not chafe against the panel edge in the body where it exits the rubber grommet in its right-hand mounting.


  • Insert a piece of wire under the rear edge on the load floor support along the thick cable harness and forward.

  • Tape the connector and a piece of the cable on the routed cable harness (Image B) on the wire.

  • Carefully pull the cable harness forward.

42
IMG-328966
 

  • Clamp the cable at the cradle on the bracket for the washer hose and under the fuse holder.

43
IMG-298164
 

  • Bend off the covers over the seat's attachments and remove the screws.

44
IMG-298165
 

  • Carefully bend off the covers in the driver seat's rear attachments with a weatherstrip tool.

  • Remove the screws.

  • Move back the seat slightly to expose the front floor mat at the trailing edge.

45
IMG-297972
 

  • Remove the rear sill panel at the left front door by first prying loose the clips starting at the front and working back.

  • Unhook the panel at the rear edge.

46
IMG-298585
 

  • Remove the tunnel console's panel. It is fastened with seven clips on the inside.

47
IMG-282523
 

  • Carefully pry loose the panel with air blower all round. The panel is secured by five clips on the sides and at the top and with four mounting springs on the lower edge.

48
IMG-282524
 

  • Pull out the panel and disconnect the connector for the hazard warning lights.

49A
IMG-282526
49B
IMG-282525
 

Illustrations A and B

  • Insert a small screwdriver in the gap on the media player. Press in the inner catch and carefully pry off the surround on one side using a weatherstrip tool.

  • Repeat on the other side and remove it.

50
IMG-282527
 

  • Remove the four screws at the upper edge of the panel.

51
IMG-303365
 

  • Push in the catches on the cover, fold it downwards and remove.

52
IMG-282532
 

  • Remove the screw inside the panel.

53
IMG-282530
 

  • Remove the three remaining screws from the reverse of the centre console.

54
IMG-282528
 

  • Remove the tunnel console's right-hand side panel by carefully pulling it away starting at the front edge. The side panel is secured with five clips on the inside.

55
IMG-282533
 

  • Fold the floor mat to one side by the left-hand side of the tunnel console.

56
IMG-282543
 

  • Loosen the clips on the cable harness from the tunnel console.

  • Disconnect the connectors for the CCM.

57
IMG-282544
 

  • Loosen the connector to the keypad for CCD, if the car is equipped with this.

58
IMG-296139
 

Applies to cars with automatic transmission

59
IMG-296140
 

  • Release the shift-lock function.

  • Move the gear selector to position "D".

60
IMG-282545
 

Applies to all models

61A
IMG-282546
61B
IMG-282547
 

Illustrations A and B

  • Carefully pry off the centre console's panel starting at both sides at the rear edge. It is secured by two clips along the long sides and four hooks around the gear lever's panel.

  • Lift it up slightly and make sure that all cables are free from the gear lever carrier and components in the tunnel console, and lift it out.

62A
IMG-286854
62B
IMG-287243
 

Illustrations A and B

  • Pull the CD player out slightly and unplug the connectors on the rear side.

  • Place the CD player to one side.

63
IMG-303384
 

64
IMG-303385
 

65
IMG-303804
 

  • Remove the screws from the front edge of the storage compartment, which holds the tunnel console at the body.

66
IMG-303805
 

  • remove the two screws in the rear storage compartment.

67A
IMG-283145
67B
IMG-275076
 

Illustrations A and B

  • Remove the screws that hold the tunnel console at the dashboard's bracket, on both sides.

68
IMG-303809
 

  • Remove the two screws at the bottom of the centre console's lower panel.

69
IMG-303810
 

  • Carefully pry at one end of the mounting bracket so that the entire centre console moves backwards a few centimetres until the bracket engages the air ducts on both sides.

70
IMG-303811
 

  • Position a small sleeve between both brackets so the centre console does not move back.

71
IMG-303812
 

For all cars with display

  • Carefully pull the panel backwards so that the screws for the display can be accessed.


Note!

Ensure that the two locating pins (small image) exit their holes and are not bent when the panel is bent backwards. If necessary, press the tunnel and centre console backwards further.


72
IMG-303813
 

  • Remove the four screws.

73
IMG-303815
 

  • Disconnect the two connectors from the display and place them to one side.


Note!

The cables may be short.


74
IMG-352251
 

  • In cases where a connector is connected to the designated position, loosen the connector, fold back the cable and secure the connector to the existing cable harness.

  • Use: Electrical tape.

75A
IMG-329230
75B
IMG-329253
 

Applies to all models

Illustration A

  • Continue to route cable harness A from the camera in the boot lid under the insulation mat at the existing cable duct and to the door opening in the left-hand rear door.

Illustration B

  • Pull out the B post panel at the lower edge until the two clips release.

  • Continue to route the cable harness in front of the B-pillar panel and to the front of the car to the joint between the front and rear floor mat.

76A
IMG-329254
76B
IMG-303834
 

Applies to left-hand drive cars

Illustrations A and B


Note!

Check that the correct connector is positioned under the seat respectively tunnel console.


    Routing cable harness B

  • Take cable harness B from the kit and route it into the mat joint under the left-hand seat towards the tunnel console and in front of the mat. Leave some cable, approximately 350 mm (13 3/4 ") in length, outside the mat joint, so that it can later be connected to the control module that is to be positioned there.

  • Route it through the tunnel console, in front of the air ducts and out on the other side. If necessary, use a piece of wire to route the cables through.

77
IMG-329255
 

Applies to right-hand drive cars


Note!

Check that the correct connector is positioned under the seat respectively tunnel console.


    Routing cable harness B

  • Route the cable harness into the mat joint under the driver's seat towards the tunnel console, in front of the mat and out onto the floor. Leave some cable, approximately 350 mm (13 3/4 ") in length, outside the mat joint, so that it can later be connected to the control module that is to be positioned there.

78
IMG-329256
 

Applies to all cars that do not have a pre-mounted display.

    Routing cable harness C

  • Take cable harness C from the kit. The shorter ground lead has a lot of excess that can be hidden under the mat by the left-hand seat.

79A
IMG-329257
79B
IMG-329258
 

Illustration A

  • Tilt the left-hand seat back.

  • Place the two large connectors for the cable harness where the two 32-pin connectors were previously disconnected from each other.

  • Route the thinner ground leads (1) into the mat joint in the same direction as cable harness B, along the member for the front seat mounting where the control module will be installed later on.

  • Pull up the shorter ground lead (2) from the mat joint so that approximately 350 mm 13 3/4 " protrudes from the mat joint.

  • Continue to route the longer of the ground leads the same way as cable harness A backwards towards the rear crossmember.


Note!

Ensure that the cables do not come into contact with moving parts in the tunnel console and that they are not at risk of being cut.


Illustration B

    Only applies to left-hand drive vehicles.

  • Route through the thicker cable (3) to the display through the tunnel console in front of the air ducts and out the other side. Use a wire to route the cables through, if necessary.

80
IMG-329259
 

    Routing the ground cable in cable harness C, continued

  • route the ground lead the same way as cable harness A towards the rear crossmember.

  • Press the B pillar panel into place again.


Note!

Ensure that the ground cable is routed so that it is not at risk of being trapped or cut by sharp edges or similar.


81
IMG-329260
 

  • Clamp the ground cable using cable ties at the rear edge of the cable duct.

  • Press two cable ties with edge clips in the bracket legs for the electric parking brake, or media player, and clamp the cable to these.

82
IMG-303863
 

  • Clean the marked surfaces on the of the rear crossmember and floor using isopropanol and wipe dry.

83
IMG-303865
 

  • Secure the cable using wide pieces of silver or woven tape along the rear crossmember and to the floor.


Note!

The ground lead must only be taped at the rear crossmember, it must not be secured by the thick cable harness.


84
IMG-303867
 

  • Connect the ground lead's ring cable terminal to the ground terminal closest to the spare wheel well.

  • Tighten the ground screw. Tighten to 10 Nm (7.5 lbf.ft.).

85
IMG-329261
 

  • Cut off the cable terminal on the short ground lead in cable harness C. A new cable terminal is in the kit.

86A
A3700183
86B
A3700174
 

Illustration A

Splicing the ground lead in cable harness C

Splicing with insulated damp-sealed crimping sleeve

Colour

Cable area, mm²

Stripping length mm

Green/White

0.3 - 0.5

5

Red

0.5 - 1.0

6

Blue

1.0 - 2.5

7

Yellow

4.0 - 6.0

7


  • Splice the black ground lead in cable harness C and the cable splice from the kit.

Illustration B

  • Strip the the cable end in accordance with the above table. Use stripping pliers, P/N 9512620.

87A
D3701802
87B
A3700181
87C
A3700188
 

Pressing the sleeve

Illustration A

  • Insert the crimping sleeve in the press tool P/N 9512785. Select the socket as per colour coding. Clamp the pliers together slightly, but only so that the crimping sleeve remains in the pliers.

  • Insert the cable in the crimping sleeve until it reaches the stop.


Note!

Make sure that the cable insulation does not come into the press area of the sleeve or that the stripped part or the cable extends outside of the sleeve.


Illustrations B and C

  • Press the legs of the pliers completely together to ensure a proper splice. The pliers will then release automatically.

  • With your hand, check that the crimping sleeve is securely in place.

88A
D3701792
88B
A3700190
 

Heating the crimping sleeve

Illustrations A and B

  • Place a suitable shield behind the cables to be crimped to prevent thermal stress to the surrounding area.

  • Warm the sleeve with a hot air gun, P/N 9512777, and suitable nozzle. It is extremely important that the crimping sleeve be securely crimped around the cable. You should be able to see that a little bit of glue has been forced out around the cable. (Illustration B).

89
IMG-329262
 

Applies to all models

  • Take the pre-routed power lead with the green connector from under the mat at the left-hand seat's left front mounting.

90
IMG-329263
 

Applies to all cars that do not have a pre-mounted display.

  • Pry up the catch on the green connector.

91
IMG-329264
 

  • Take special tool, part no. 9512637 and carefully press into the hole above the cable terminal in position 1 to release the catch.

  • Pull out the existing black cable.

92
IMG-329265
 

  • Carefully push the new cable terminal on the newly spliced ground lead into Pos 1 in the connector.

  • Press the connector's catch securely into place.

93
IMG-329266
 

  • Insulate and tape the excess cable terminal at the connector's cable harness.

94
IMG-329267
 

  • Place the cables in the cut-out in the floor mat.

95
IMG-329272
 

  • take control module, bracket and two screws from the kit.

  • Tighten the control module to the bracket.

96
IMG-329273
 

  • Press the clip with cable tie into the bracket's lower hole.

97
IMG-329274
 

  • Take the control module with bracket and connect all pre-routed cables to it.

98
IMG-329275
 

  • Collect the cables and clamp them using the cable tie in the bracket.


Note!

Ensure that the cables are correctly positioned and bent at the connectors.


  • If necessary, insert any excess inside the floor mat.

99
IMG-329276
 

  • Install the control module with bracket using screws from the kit.

100
IMG-298584
 

101
IMG-298586
 

102A
IMG-303868
102B
IMG-303869
 

Applies to left-hand drive cars

Illustrations A and B

    Routing cable harness B/cable harness C

  • Insert the wire into the centre console, up towards the compartment above the air outlet and out through the hole on the right-hand side in the compartment where the display is to be positioned.

  • Tape the connector and a piece of the cable(s) at the spring wire.

  • Route the cable(s) on the right-hand side in the compartment where the media player was located.

  • Pull the cable(s) forward.

103A
IMG-303883
103B
IMG-303884
 

Applies to right-hand drive cars

    Routing cable harness B/cable harness C

  • Insert the wire into the centre console, up towards the compartment above the air outlet and out through the hole on the left-hand side in the compartment where the display is to be positioned.

  • Tape the connector and a piece of the cable at the wire spring.

  • Route the cable(s) on the left-hand side in the compartment where the media player was located.

  • Pull the cable(s) forward.

104
IMG-352253
 

Applies to all with a mounted display

  • Connect the remaining connector to the display.

  • Connect the connectors to the display.

105
IMG-352252
 

  • Connect the connector on the routed cable to display.

106
IMG-329278
 

Applies to all where the display is included in the kit.

  • Carefully pull the panel back so that the new display can be installed.


Note!

Ensure that the two locating pins (small image) exit their holes and are not bent when the panel is bent backwards. If necessary, press the tunnel and centre console backwards further.


107
IMG-352257
 

  • Take the display from the kit.

  • Connect the connector from the routed cable for the power supply to display.

108
IMG-352256
 

  • Connect the connector on the routed cable to display.

109
IMG-303887
 

Applies to all models

  • Reinstall the display.

  • Take screws from the kit or use existing screws and tighten the display.


Note!

Do not damage the display and panel.


110
IMG-303888
 

  • Move the panel back into place and ensure that the locating pins enter their holes.

111
IMG-303889
 

  • Remove any spacers.

112
IMG-303890
 

  • Move the centre console back into position.

113
IMG-303891
 

114A
IMG-303892
114B
IMG-303893
 

115
IMG-303894
 

116
IMG-303895
 

117
IMG-303896
 

118
IMG-303897
 

119A
IMG-282557
119B
IMG-282558
 

Illustrations A and B

  • Take the panel with CCM and insert the cables in the tunnel console.

  • Place it at the upper edge and secure it with clips at the rear edge.

  • Secure the panel in the centre console. Make sure that all clips engage.

120
IMG-282559
 

121
IMG-282560
 

Applies to all cars that have a pre-mounted display.

122
IMG-282561
 

123
IMG-303943
 

Applies to cars that do not have a pre-mounted display.

  • Connect the connector (1) that was disconnected from the tunnel console's left-hand side to the corresponding connector (2) in the routed adapter cable.

  • Attach clips to the cable harness in the tunnel console.

  • Connect the remaining connectors to each other.

  • Wrap foam tape around the loose connectors and position them inside the mats so that they do not move.

  • Secure the long cables at the existing cable harness using cable ties from the kit.

124
IMG-303965
 

Applies to all models

125
IMG-303966
 

126
IMG-282566
 

127
IMG-282564
 

128
IMG-282565
 

129A
IMG-303983
129B
IMG-303984
 

Applies to cars that do not have a pre-mounted display.

Illustrations A and B

    Replacement of the panel for the air vent

  • Poke the catches downwards using a small screwdriver.

  • Fold down the air nozzle and unhook it from the four mounting eyelets at the lower edge of the panel.

130
IMG-303985
 

  • Poke the catches on the hazard warning button in and push the button out.

  • Place the panel to one side and take new screws from the kit.

131
IMG-303987
 

132
IMG-303988
 

133
IMG-282568
 

Applies to all models

  • Connect the hazard warning light connector.

134
IMG-282569
 

  • Secure the panel. Make sure that all air nozzles align correctly in the air ducts in the dashboard and that all clips and catches engage.

135
IMG-282567
 

  • Reinstall the tunnel console's panel on both sides.

136
IMG-255787
 

137
IMG-304003
 

138
IMG-304005
 

139
IMG-304007
 

140
IMG-304008
 

141
IMG-304009
 

142
IMG-268064
 

143
IMG-268106
 

144
IMG-328944
 

Applies to cars with electrically heated seat cushions

145
IMG-268107
 

Applies to all models

146
IMG-304010
 

147
IMG-304011
 

148
IMG-304012
 

149
IMG-304013
 

  • Install new clips in the lower panel.

  • Pull the cables for the lighting and contact for the door opener out through the hole in the panel.

  • If the car is equipped with a KV antenna, connect its connector.

  • Secure the panel and ensure that all clips have engaged.

150A
IMG-304014
150B
IMG-304015
 

Applies to cars with electric opener for boot lid

151
IMG-304016
 

Applies to all models

152A
IMG-304017
152B
IMG-304018
 

153
IMG-304019
 

  • Check that all clips are intact and properly positioned. Replace any broken clips.

  • Reinstall the upper panel by first pressing the upper edge and then the sides at the same time as aligning the lower panel.


Note!

Make sure that the clips align with their holes.


154
IMG-291605
 

155
IMG-291606
 

156
IMG-332195
 

  • Set the ignition switch to position II.

157
IMG-242268
 

Download the software (reload) for the accessory's function following the service information in VIDA.

31268489

158
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.

    30786701

159
IMG-275777
 

    Calibrate according to:

  • DIAGNOSTICS/

  • VEHICLE COMMUNICATION/

  • Advanced/

  • PAC/

  • Service calibration, parking camera