Pokyny pro instalaci

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC90 2012
XC90 (03-) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307565601.230756177
Multimedia monitor with DVD, Dual screen




 
Equipment
IMG-242205
A0000162
IMG-262943
IMG-239942
IMG-239981

IMG-317184

IMG-317185

IMG-317186

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Note!

There are two versions of cable harness for the tunnel console, with or without preparations for Digital TV receivers.

The images in the installation instructions show cable harness without Digital TV receiver.


1
IMG-256044
 

  • Slide both the front seats all the way back and upwards all the way at the front and rear edge.

  • Press the headrest downwards.

  • Find the headrest's two locks on the back of the seat. Press in the catches and pull the headrest upwards at the same time.

  • The seats may require lowering slightly at the rear edge again so that the headrest can be pulled out of the backrest completely. Therefore lower the seat as much as possible so that the headrest can be released and removed. Remove the headrest on both front seats and allow the seats to remain in the same position.

2
R8504225
 

  • Remove both the side panels from the tunnel console.

3
R8504495
 

  • Remove the sound barrier on the driver's side by first removing the two screws and then prizing it away at the top edge.

4
IMG-238927
 

  • Pull the handle (1), move the tunnel compartment backward and lift it away (2).

5
R8503994
 

  • Remove the cover. It shall not be re-used.

6
R8504113
 

Applies to cars with automatic gearbox

  • Turn the ignition key to position II.

Applies to all models

  • Move the gear selector lever to its rearmost position.

  • Use a weatherstrip and pry off the gear selector panel at the rear edge.

7
IMG-245980
 

  • Turn the ignition key to position 0.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.


8
IMG-239204
 

  • Press in the catches underneath and remove the panel.

9
IMG-268403
 

  • Remove the small storage compartment.

10
R3904067
 

Applies to cars with telephone

  • Unhook and disconnect the connector (1).

  • Disconnect the telephone cable from the load-removing grommet (2).

  • Release the telephone cable.

  • Remove the handset.

  • Remove the screw (3).

  • Push the catch to one side (4).

  • Remove the telephone cradle.

11
IMG-268404
 

Applies to all models

  • Remove the six screws.

12
IMG-268405
 

  • Lift up and remove the upper section.

  • At the same time disconnect the connector to the AUX socket.

13
IMG-268406
 

  • Disconnect the connector. Press in the catches and unhook it from the tunnel console.

14
IMG-268407
 

  • Remove the two screws and lift out the tunnel console.

15
IMG-317323
 

  • Take the cable harness (C) from the kit and position it as illustrated.

  • The junction (1) must be at the rear edge of the SRS control module. The cable marked with blue tape must go to the right seat and the other to the left seat. The cable with 2 x 4 pin connectors must be routed forward on the driver's side.

16
IMG-268409
 

  • Route the cables in the join for the floor mats further along the seat rail.

  • Position the cable in a loop under the seat.

17
IMG-268410
 

  • Take the cable with the two 4 pin connectors and route forward on the driver's side.

18
IMG-268411
 

Carry out points 18-45 on both sides of the seats

  • Remove the screw for the seat's side panel.

19
IMG-268412
 

  • Turn the panel upwards at the front edge.

  • Unhook it from the seat at the rear edge.

20
IMG-268413
 

  • Remove the knob for the lumbar support adjustment by removing the cover using a small screwdriver and pull the knob straight off.

21
IMG-268414
 

  • Take a long cable tie from the kit and insert it through the hole for adjusting the lumbar support and inside the upholstery. The cable tie must be routed between the thin foam of the upholstery and the support pad.

22A
IMG-262949
22B
IMG-317223
 

Illustrations A and B

  • Remove cable harness (A) from the kit.

  • Tape the cable terminals on the cable tie. Tape together as flat as possible. (Image B) Route the cable harness through and out at the headrest hole.

  • Remove the cable tie from the cable harness.

23
IMG-262950
 

Applies to the right-hand front seat

  • Thread the cable tie from the headrest's inner mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29).

24
IMG-262952
 

Applies to the left-hand front seat.

  • Thread the cable tie from the headrest's outer mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29).

25
IMG-262951
 

Applies to both seats

  • Tape the cable harness on the cable tie. Tape as flat as possible. See image 22 B.

  • Pull it up towards the upper edge of the seat and out through the hole for the headrest.

  • Remove the cable tie and tape from the cable harness.

26
IMG-317224
 


Caution!

There are two brown cables in the cable harness.

The brown cable to terminal 4 is twinned with the blue cable to terminal 3.


Position:

  1. Not connected.

  2. White (W)

  3. Blue (BL)

  4. Brown (BN)

  5. Red/White (R/W)

  6. Red (R)

  7. Black (SB)

  8. Brown (BN)

  9. Yellow (Y)

  10. Green (GN)

  11. Gray (GR)

  12. Pink (P)

27
IMG-317243
 

  • Take the grey connector from the kit. Connect the cable harness terminals according to point 26.

  • Press in the connector's catch.

28
IMG-317244
 

  • Adjust the length on the cable harness so that the connector protrudes 140mm. The cable harness must be positioned in front of the hole for the headrest.

29
IMG-262956
 

  • Using your fingers, press the cable harness under the protective pad, the cable harness must not press out the upholstery after installation.

  • 1. Padding

    2. Protective pad

30
IMG-317245
 

  • Take the headrest and the upholstery from the kit. Pull the upholstery over the headrest.

31
IMG-317263
 

  • Pull the two corners of the upholstery over.

32
IMG-317325
 

  • Hook the upholstery onto the two cutouts.

33
IMG-317326
 

  • Fold in the upholstery's two reinforcements.

34
IMG-317327
 

  • Fold up the upholstery's reinforcement.

  • Locate the hole under the upholstery on the side of the headrest.


Note!

The inward facing side in the car.


  • Make a mark for making a hole using a piece of tape.

  • Fold back the upholstery's reinforcement.

35
IMG-317328
 

  • Install the 5 clips.

36
IMG-317329
 

  • Fold in the upholstery's mounting.

37
IMG-317330
 

  • Take the display from the kit.

  • Install on the headrest.

38
IMG-317331
 

  • Align the display in the headrest's two cutouts.

39
IMG-317332
 

  • Install the two screws.

40
IMG-317333
 

  • Locate the hole under the upholstery on the headrest side, marked with tape.

  • Make a hole in the upholstery using a scriber or an awl.


Note!

The inward facing side in the car.


41
IMG-317334
 

  • Take the coat hook from the kit.

  • Press into the hole.

  • Tap it in lightly using a plastic hammer so that it secures properly.

42
IMG-317335
 

  • Position the panel on the seat.

  • Position the cable harness in the panel's cutout.

43
IMG-317336
 

  • Install the headrest on the seat.

  • Only slide it down so that the distance between the seat and lower edge of the headrest is approximately 50mm.

44
IMG-317337
 

  • Connect the connector and push the headrest down to the locked position.

  • Check that the head restraint has locked into place by pulling it upwards.

45
IMG-317338
 

  • Check that the headrest upholstery is correctly aligned against the panel.

  • Repeat steps 18-45 for the other side.

46
IMG-263002
 

Applies to the right-hand front seat and cars without heated seats

  • Take a clip with cable tie from the kit and install it on the plate edge on the left-hand side of the right-hand seat.

47
IMG-263003
 

  • Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the seat belt buckle.

  • Tighten the cable tie (1).

  • Secure the cable using two cable ties (2).

48
IMG-263004
 

Applies to the right-hand front seat and cars with heated seats

  • Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element.

  • Secure the cable using three cable ties (1).

49
IMG-263005
 

Applies to the right-hand front seat

  • Route the cable harness in an arc under the seat.

  • Secure it using three cable ties in the existing cable harness.

50
IMG-263006
 

  • Take a piece of foam tape from the kit and cut it in the centre.

  • Fold the seat forward slightly and connect the cable harness from the floor to the connector (1).

  • Tape one cut piece of foam tape around the connectors.

  • Place a cable tie on each side of the connectors and tighten.

  • Check that the cable harness is not trapped when the seat is slid forwards and backwards.

    The right-hand seat means the passenger seat

  • Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest.

51
IMG-263009
 

Applies to the left-hand seat and cars without heated seats

  • Take a clip with cable tie from the kit and install it on the plate edge on the right-hand side of the left-hand seat.

52
IMG-263010
 

  • Take the cable harness from the headrest and pull forward, underneath the seat. Follow the cable harness for the seat belt buckle.

  • Tighten the cable tie (1).

  • Secure the cable using two cable ties (2).

53
IMG-263011
 

Applies to the left-hand front seat and cars with heated seats

  • Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element.

  • Secure the cable using three cable ties (1).

54
IMG-263012
 

Applies to the left-hand front seat.

  • Route the cable harness under the seat.

  • Connect the cable harness from the floor to the connector (1).

  • Secure it using a cable tie in the existing cable harness or in a bracket.

  • Tape one cut piece of foam tape around the connectors.

  • Place a cable tie on each side of the connectors and tighten.

  • Check that the cable harness is not trapped when the seat is slid forwards and backwards.

    The left-hand seat means the passenger seat

  • Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest.

55
IMG-268416
 

Applies to all models

  • Fold the ashtray out, press it down and remove

56
IMG-268417
 

  • Pull out the cup holder to its limit position.

57
IMG-268418
 

  • Turn the tunnel console.

  • Lift up the catch and remove the cup holder.

58
IMG-268419
 

  • Remove the four screws.

59
IMG-268444
 

  • Pull the opening handle.

  • Remove the two screws and lift off the lower section.

60
IMG-268445
 

  • Fold the cover up and remove the two screws.

  • Remove the cover by sliding it forward. The cover will not be reused.

61
IMG-268446
 

  • Remove the plug for the 12 V socket.

  • Remove the two rubber supports.

62
IMG-268447
 

  • Lift up the two catches and remove the inner section of the ashtray. It will not be reused.

63
IMG-268448
 

  • Release the two catches and remove the 12 V socket.

64
IMG-268450
 

  • Mark as illustrated on the tunnel console's storage compartment.

  • Pre-drill using a Ø 2.5 mm (3/32") bit.

  • Drill out the hole. Use a Ø35 mm (1 3/8") diameter hole saw.

  • Smooth off the hole edges.

65
IMG-268451
 

Points 65 - 66 apply when the tunnel console is not prepared for the RSE system

  • Mark as illustrated on the tunnel console's upper section.

  • Drill using a Ø 5mm (13/64") bit.

66
IMG-268452
 

  • Mark as illustrated on the tunnel console's upper section.

  • Saw and cut out the hole according to the markings.

67
IMG-268453
 

Applies to all models

  • Take the lower section of the cover and cable harness (B) from the kit.

  • Insert the end with the three (4 x with Digital TV receiver) connectors through the hole.

  • Install the rubber grommet.

68
IMG-268454
 

  • Secure the cable harness with a tie strap.

69
IMG-268456
 

  • Take the DVD unit and 4 M4x6 screws from the kit.

  • Connect the three (4 x with Digital TV receiver) connectors to the DVD unit.

70
IMG-268457
 

  • Place the DVD unit in the lower section of the cover as illustrated. Ensure that the cable harness goes under the DVD unit and does not protrude towards the open button or screw tower.

  • Install the four screws and tighten.

71
IMG-268458
 

  • Take the cover's upper section and 4 screws, PF5x16, from the kit.

  • Install the cover.

72
IMG-268467
 

  • Turn the cover, install the four screws and tighten to 3 Nm (2.2 lbf.ft.).

73
IMG-268459
 

  • Route the cable harness in from the DVD unit through the drilled hole and down on the right-hand side of the tunnel console.

  • Install the rubber grommet.

  • Check that the rubber grommet's flanges are against the console.

74
IMG-268460
 

  • Take the AV panel from the kit.

  • Connect the green connector to it.

75
IMG-268464
 

  • Install the 12 V socket to the panel.

76
IMG-268466
 

  • Secure the cable harness clips on the flange of the AV panel.

77
IMG-268468
 

  • Press the panel into place.

  • Secure the panel with one screw (ST 3.5x13) from the kit.

78
IMG-268471
 

  • Reinstall the rubber support, the ashtray and the plug for the 12 V socket.

79
IMG-268472
 

  • Install the cover on the tunnel console and tighten with the two screws.

80
IMG-268473
 

  • Open and close the cover three times.

  • Check that the lock at the front edge works and that the rubber bushings are in place.

  • The cable harness should be in a loop as illustrated.

81
IMG-268476
 

  • Turn the console and route the cable harness as illustrated.

82
IMG-268487
 

  • Thread the cable harness out through the square cut out on the lower section of the tunnel console.

  • Secure the two clips of the cable harness on the plastic flanges.

  • Tighten the lower section using the 6 screws.

83
IMG-268488
 

  • Take a cable tie and secure the 12V socket's cable by the clip on the cable harness from the DVD unit.

  • The cable tie catch should point towards the outer side of the tunnel console.

  • Reinstall the cup holder.

84
IMG-268489
 

  • Make marks for drill holes on the opening handle for the tunnel console as illustrated.

  • Pre-drill using a Ø 2.5 mm (3/32") bit.

  • Drill out the hole using a Ø 6 mm ( 15/64") drill bit.

85
IMG-268490
 

  • Take the cover and 2 x PF5x12 screws from the kit.

  • Install the cover on the opening handle.

Digital TV receivers must then be installed:

Continue with the installation instructions: TV receiver, digital.

86
IMG-268491
 

  • Reinstall the front tunnel console and at the same time pull up the connectors for the RSE system, 12 V socket and telephone if applicable.

87
IMG-268492
 

  • Connect the 4 pin black connector from the cable harness (B) to the one disconnected from the AUX socket.

88
IMG-268493
 

  • Take the upper panel for the front tunnel console.

  • Remove the AUX socket by releasing the catches at the front and rear edge.

89
IMG-268494
 

  • Take the new AUX socket from the kit and connect it to the 7 pin connector from cable harness (B).

  • Install the socket in the panel with the connector's catch backwards.

90
IMG-268496
 

  • Install the tunnel console's upper panel.

  • Check that the panel hooks securely at the front edge.

  • Reinstall the tunnel console's 8 screws and tighten them.

91
IMG-268497
 

Applies to cars with telephone

  • Reinstall the telephone cradle with the screws (3).

  • Route the telephone cable.

  • Install the telephone cable in the load-removing grommet (2).

  • Connect the connector (1).

92
IMG-268498
 

Applies to all models

  • Connect the connector for the 12V socket.

93
IMG-268499
 

  • Take the rear tunnel console.

  • Connect the two connectors for the RSE system (3 x with Digital TV-receiver.)

  • Take two pieces of foam tape from the kit and wrap them around the connectors. Cut off the foam tape excess.

94
IMG-268500
 

  • Insert the connectors into the tunnel console.

  • Hook the connector on for the 12 V socket.

  • Slide the rear tunnel console forwards in its grooves until it locks and check that the cable harness is not trapped.

95
IMG-268501
 

  • Take the cable with the 2 x 4 pin connector and route forward on the driver's side.

  • Fold the carpet to one side and place the cable underneath.

96
IMG-241303
 

  • Locate the 4 pin, grey connector for the power supply. It is secured on the thick cable harness under the dashboard on the driver's side.


Note!

The pre-routed connector is already connected on certain versions.


97
IMG-268502
 

  • Connect the cable harness to the existing connector (1).

  • Wrap a piece of foam tape around the connected connectors and cut off the excess.

  • Install the connector (2) on the car's existing cable harness using a cable tie.


Note!

The pre-routed connector is already connected on certain versions. In such a case, disconnect it and connect both connectors from the new cable harness. Wrap a piece of foam tape around the connectors.


    Reinstall:

  • the small storage compartment

  • the panel at the gear selector

  • side panels

  • the sound barrier

98
IMG-275777
 

  • Install the batteries in the remote control and headsets.

  • Region code the DVD player. Information is in VIDA under:

  • Product specifications

    Design and Function

    39 Media, communication and navigation

    393 Equipment for entertainment

    Rear seat entertainment system

    Design

    To activate the TV function

  1. Aim the remote control at the screen and press DAY/NIGHT ("on/off") for approx. 5 seconds until SERVICE MENU is displayed.

  2. Enter code 1971, press OK.

  3. Select SET TV, press OK.

  4. Select TV connected, press OK.

  5. Exit.

99
R8903555
 

Installing decals (Only applies to USA and Canada)

  • Take the black decal from the kit.

  • Clean the area (1) where the decal will be located. Use a mixture of 30% windscreen washer fluid and 70% water. Wipe dry.

  • Remove the backing paper from the adhesive side of the decal. Secure the decal as illustrated.

  • Press the decal into place properly.