Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2016
XC70 (08-) 2016

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314088641.331470252, 31428816, 31435840, 31435857
Parking assistance, camera, rear




IMG-389852




 

Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46


Materials

Designation

Part number

Electrical tape


Equipment
IMG-242205
IMG-345497
IMG-239664
IMG-239660
IMG-240693
IMG-239981
IMG-268803

IMG-402010


 
  

Parking assistance, camera, rear

 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Color symbols

2
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Preparation

3
IMG-335491
 
 

Removal

4
IMG-273525
 
5
IMG-273526
 
6
IMG-268004
 
7
IMG-268005
 
8
IMG-268007
 

Remove the screws.

9
IMG-268009
 

Remove the screw.

Detach the panel.

Repeat on the other side.

10
IMG-268011
 

Remove the part carefully

11
IMG-268010
 

Caution!
Pull carefully.

Remove the part carefully

Disconnect the connector, if applicable.

12
IMG-392004
 

Caution!
Check that the component does not show deformation damage.


Note!
The marked component is a spare part and can be replaced with a new if necessary.

13
IMG-392050
 

Caution!
Check that the component does not show deformation damage.


Note!
The marked component is a spare part and can be replaced with a new if necessary.


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

14
IMG-402015
 

Remove the part carefully

15
IMG-402022
 

Disconnect the connector.

16
IMG-402021
 

Remove the screw.

17
IMG-350221
 

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

18
IMG-401980
 

Remove the panel.

19
IMG-399272
 

Remove the panel.

20
IMG-259759
 

Remove the screws.

21
IMG-268016
 

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

 

Accessory installation

22
IMG-402036
 

Note!
Orientation view

23
IMG-402035
 

Place the component where indicated in the graphic.

Scribe/mark up

24
IMG-402051
 

Caution!
Make sure to protect adjacent surfaces or components.

Use tape

25
IMG-402046
 
26
IMG-402048
 
27
IMG-389402
 

Note!
Note the position.

28
IMG-389380
 
29
IMG-389429
 

Loosen the wiring harness or move it to the side.

30
IMG-389794
 
  1. Install component that comes with the accessory kit.

  2. Install the screws.

31
IMG-402001
 

Repeat on the other side.

32
IMG-401994
 

Repeat on the other side.

33
IMG-402055
 

Tape the cables on the cable tie.

Use: , Electrical tape

34
IMG-402056
 

Pull the wiring through.

35
IMG-389588
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Pull the wiring through.

Remove the cable tie(s).

36
IMG-401912
 
37
IMG-399835
 

Connect the cable harness terminals in the connector as follows.

38
IMG-401095
 

Depress the secondary lock.

39
IMG-389796
 

Connect the connector.

Clamp the cables and connectors to the existing cables to prevent noise.

 

Installation

40
IMG-402060
 
41
IMG-402075
 
42
IMG-402070
 
 

Accessory installation

43
IMG-399270
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

44
IMG-399271
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Route the wire adjacent to existing wirings.

Use a cable tie

Install the cable.

45
IMG-353734
 

Connect the cable.

46
IMG-353736
 
 

Vehicles with towbar

47
IMG-391287
 

Note!
Note the position.

Connect the cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

 

Vehicles without tow hitch.

48
IMG-391291
 

Connect the cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

 

All vehicles

 

Removal

49
IMG-346689
 

Remove the rubber strip.

50
IMG-338119
 

Remove the panel.

51
IMG-346676
 

Caution!
The front and upper sill panel must be removed and installed as one unit.

52
IMG-346681
 
53
IMG-346677
 
54
IMG-346682
 
 

Vehicles with integrated child safety seat

55
IMG-319024
 
56
IMG-319025
 

Remove the screws.

 

All vehicles

57
IMG-402030
 

Remove the marked part.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

58
IMG-402031
 

Remove the panel.

59
IMG-402025
 

Detach the panel.

60
IMG-347139
 

Remove the panel.

When removing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

61
IMG-355521
 

Remove the screws.

Detach the panel.

62
IMG-355519
 

Disconnect the connector.

Remove the panel.

63
IMG-354313
 

Remove the panel.

Disconnect the connector, if applicable.

64
IMG-357381
 

Remove the screws.

65
IMG-373498
 
66
IMG-357380
 

Remove the screws.

Note the position.

67
IMG-373518
 
68
IMG-356889
 

Disconnect the connector.

69
IMG-357382
 

Unhook the cable harness clips.

70
IMG-373518
 

Remove the marked part.

71
IMG-354292
 
72
IMG-354291
 

Remove the panel.

73
IMG-349806
 

Remove the screws.

74
IMG-345282
 

Remove the screws.

 

Cars with automatic transmissions

75
IMG-293006
 
76
IMG-293007
 
 

All vehicles

77
IMG-353601
 
78
IMG-353602
 
79
IMG-349826
 

Caution!
Be careful not to damage the catches.

Detach the panel.

80
IMG-349942
 

Remove the screws.

81
IMG-349946
 
 

Accessory installation

 

Left hand drive vehicles

82
IMG-390146
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Position/route the cable harness as illustrated.

83
IMG-390151
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Route the wire adjacent to existing wirings.

 

Right-hand drive vehicles

84
IMG-390263
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

Route the cable harness to the existing cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

 

All vehicles

85
IMG-384929
 

Connect the prerouted cable.

86
IMG-349948
 

Reinstall the removed part.

87
IMG-390597
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Fold the carpet aside.

Pull the wiring through.

Route the cable harness to the existing cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

88
IMG-401933
 

Note!
Orientation view

89
IMG-400319
 

Depress the locking device.

Release the connector's catch.

Disconnect the connector.

90
IMG-387423
 

Release the catches.

Remove the marked part.

91
IMG-400415
 

Release the connector's secondary lock.

Lift approximately 2 mm.

92
IMG-401921
 

Connect the cable harness terminals in the connector as follows.

93
IMG-400381
 

Note!
Note the position.

94
IMG-387424
 

Reinstall the removed parts in reverse order.

Reinstall the removed part.

95
IMG-400420
 

Connect the connector.

96
IMG-400000
 

Reinstall the removed parts in reverse order.

 

Removal

97
IMG-382371
 

Note!
Orientation view

98
IMG-381005
 

Measure and mark as illustrated.

99
IMG-381006
 

Use a drill with the stated size

100
IMG-381020
 


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

101
IMG-380996
 
 

Accessory installation

102
IMG-382374
 

Install component that comes with the accessory kit.

 

Installation

103
IMG-377070
 

Reinstall the removed parts in reverse order.

104
IMG-336901
 
105
IMG-336904
 

Warning!
When switching the ignition on for the first time after a battery disconnect and connect, make sure to stand outside the vehicle and only reach into the vehicle keeping clear of the air bag deployment areas.

106
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31428822

107
IMG-354602
 

Warning!
Check for correct operation after the installation.