| | Applies to the S60 and V70 up to and including model year –2004 |
| | M8600440 |
|
| | Applies to the S60 and V70 up to and including model year –2004 Preparations |
| | M8600441 |
|
| | Note!
When cutting along the upper horizontal line, angle the knife towards the upper edge of the molding. Guide the knife along the molding. This is so that the cut is not positioned in the center of the curvature of the molding. |
|
| | M8600442 |
|
| | Reinstall the overrider molding. Install the front socket's protective cover (1) in the overrider molding. Mark out the hole in the bumper cover (2) using a Ø29 mm (1 1/8") diameter hole saw and its central drill bit. Remove the protective cover and drill out with the Ø29 mm (1 1/8") diameter hole saw. Remove any swarf. Reinstall the protective cover.
|
| | D2000257 |
|
| | Remove: the screw (1) from the left-hand air baffle (2). the left-hand air baffle by pulling it backwards. the right-hand air baffle in the same way.
|
| | D2000231 |
|
| | Remove: the air baffle (2) by undoing the screws (1), pressing up the catches (5) and moving the air baffle down and back. the engine splash guard (4) by undoing the screws (3).
|
| | M2900133 |
|
| | Installing the front engine block heater socket Route the cable belonging to the front socket through the protective cover (1) and the bumper cover (2). Install the plastic nut (3) from the kit on the front socket and tighten. The cover fits horizontally and opens forwards.
Hint
The nut is difficult to access. It can be easier to screw in with the cable instead. |
|
| | Applies to the S60 and V70 from model year 2005– |
| | M8601194 |
|
| | Applies to the S60 and V70 from model year 2005– Preparations Measure out the hole for the front socket as illustrated. The measurement between the centre of the hole and the corner of the headlamp must be 200 mm (7 7/8"). Measure out the hole's centre so that it is symmetrically located on the top of the bumper. Pre-drill the hole using a Ø3 mm (1/8") bit. Drill out the hole. Use a Ø30 mm (1 3/16") diameter hole saw. Remove any swarf.
|
| | M3703484 |
|
| | |
| | M8601252 |
|
| | Install the expander nut in the hole, with the guide pin in the guide hole. Route through the cable from the front socket, including the ground cable, from above and down. Let them hang down.
|
| | M8601253 |
|
| | Installing the front engine block heater socket Connect the cable to the front socket. Press down and turn the cable clockwise so that the expander nut expands. Align the cable from the front socket so that the hinge points to the headlamp. Remove the cable.
|
| | |
| | R3501343 |
|
| | Applies to the XC90 Preparations |
| | R3501493 |
|
| | Carefully prize up the catch on the connector for the headlamp with a screwdriver. Pull the catch up completely, detach the connector and place the headlamp to one side.
|
| | R8600944 |
|
| | |
| | R8600921 |
|
| | Measure out for drilling the front socket hole as illustrated. Pre-drill the hole using a Ø3 mm (1/8") bit. Drill out the hole. Use a Ø29 mm (1 1/8") diameter hole saw. Remove any swarf.
|
| | R8600945 |
|
| | |
| | R8600920 |
|
| | |
| | R8703775 |
|
| | R8703776 |
|
| | Installing the front engine block heater socket Illustration A Take the front socket, protective cover and plastic nut from the kit. Fit the protective cover on the front socket's connector and turn the connector so that the cover is opened to the left-hand side of the car as illustrated.
Illustration B |
| | R2000348 |
|
| | |
| | |
| | D8600337 |
|
| | Applies to the S80 Preparations Install the adhesive template and mark out the holes on the bumper in accordance with the template. Drill a hole using a Ø4 mm (5/32") bit. Drill a hole at right angles to the surface using a Ø29 mm (1 1/8") diameter hole saw. Adjust the guide hole with a round file. In addition, adjust the lead-through hole if required.
|
| | D3701818 |
|
| | |
| | D8600338 |
|
| | Installing the front engine block heater socket Install the expander nut in the hole, with the guide pin in the guide hole. Route through the cable from the front socket, including the ground cable, from above and down. Let them hang to the ground.
|
| | D8600339 |
|
| | Connect the cable to the front socket. Press down and turn the cable clockwise so that the expander nut expands. Align the cable from the front socket so that the hinge points to the headlamp. Remove the connecting cable.
|
| | |
| | M8600602 |
|
| | Applies to the XC70 Preparations Clean the bumper cover where the two pieces of tape shall be adhered. Install the two pieces of tape for marking the holes for the engine block heater connector (use narrow tape). One piece of tape is fitted at the rear edge, under the corner of the indicator lamp, and vertically down. The second piece of tape's lower edge is fitted along the upper radius of the bumper cover as illustrated.
|
| | M8600603 |
|
| | Mark up a rectangle, in accordance with the measurements in the figure, on the inside of the corner of the point of intersection of the two pieces of tape. The distance from the tape edges must be 5 mm (13/64"). Protect the bumper cover by applying tape to the surface to be cut. Carefully cut out from the bumper cover in accordance with the marking. Use a utility knife or similar. Even off the edges.
|
| | M8600604 |
|
| | Installing the front engine block heater socket Remove the pieces of tape. Take the front socket's protective cover (1) from the kit and press it into the recess. The part of the protective cover where the hole is closer to the edge must point forward. Mark out the hole in the bracket (2) inside the bumper cover. Use a Ø29 mm (1 1/8") diameter hole saw without central drill bit. Remove the protective cover and drill out with the Ø29 mm (1 1/8") diameter hole saw. Remove any swarf.
|
| | M8600605 |
|
| | File out a small recess, 4 x 4 mm (5/32" x 5/32"), in the lower edge of the hole in the protective cover. The hole is designed for the pin on the expander nut, which is used for tightening the front socket. Reinstall the protective cover.
|
| | M8600606 |
|
| | Install the expander nut (1) in the hole. Guide down the enclosed cable (2), including the ground cable, through the hole. Take the connecting cable (3) from the kit. Fit it together with the cable at the expander nut. Screw clockwise so that the expander nut expands. Remove the connecting cable.
Note!
Ensure that the drainage hole for the front engine block heater socket is open. |
|
| | Applies to the XC70 and S80 |
| | D2000257 |
|
| | Applies to the XC70 and S80 Raise the car. Remove the screw (1) in the left air baffle (2) for the front brake. Remove the left-hand air baffle by pulling it backwards. Remove the right-hand air baffle in the same way.
|
| | D2000231 |
|
| | |
| | Installing the engine block heater, applies to all car models |
| | R8600915 |
|
| | Installing the engine block heater, applies to all car models Drill a hole in the front/lower edge of the side member with a Ø4 mm (5/32") bit. Apply anti-corrosion agent and secure the ground cable with the enclosed Ø4.8 mm (3/16") flanged screw and toothed washer (under the screw head).
Note!
Connect the ground cable to the side member, not to the subframe. |
Secure the excess ground cable with a tie strap.
|
| | A8701899 |
|
| | Installing the hose heater Open the cap for the radiator's expansion tank. Position a collection container under the engine and open the coolant cock. Drain the coolant and close the cock.
|
| | R2900479 |
|
| | |
| | R2900494 |
|
| | |
| | R2900480 |
|
| | Test mount the heater with the bracket on the existing protruding studs but without tightening the nuts. The heater and bracket should be fitted as illustrated to ensure correct function and so that the hoses fit. Remove the heater with bracket from the studs.
|
| | R2900482 |
|
| | |
| | R2900481 |
|
| | Install the heater with bracket on the studs. Fit the loose hose ends on the car's connections and tighten the hose clamps. Secure the bracket with nuts from the kit and tighten to 24 Nm (18 lbf.ft).
|
| | D2900051 |
|
| | Remove the existing nut from the steering gear. Install the bracket for mounting the branching connector and cables. Install the enclosed lock nut. Tighten to 48 Nm (36 lbf.ft).
|
| | D3601932 |
|
| | |
| | R2900492 |
|
| | |
| | R2900226 |
|
| | Applies if engine block heater and passenger compartment connector shall be fitted at the same time Install the branching connector on the bracket with screw and nut from the kit. Grease in the O-rings with low temperature grease (part no. 1161417-9) (see step 15). Connect the cables from the front socket (1), the passenger compartment socket (2) and the engine block heater (3) to the branching connector. Tighten the branching connector to the bracket for the steering gear.
|
| | Connection and finishing work, applies to all |
| | R8703667 |
|
| | Connection and finishing work, applies to all Take four tie straps from the kit and press them into the holes on the inside of the subframe. Route the cable from the front socket above the front edge of the subframe and back to the cable from the engine block heater. Clamp the cable securely into the fitted tie straps. Grease in the O-rings on the connector with low temperature grease (part no. 1161417-9) (see step 15).
|
| | IMG-364951 |
|
| | Secure the heater cable.
Caution!
The cable must not be secured to the drive shaft, to the fuel lines, air conditioning (A/C) pipes or brake pipes. Ensure that the cable is not rubbing against any sharp edges and that it is not too close to the turbocharger (TC) or exhaust pipe to prevent damage from radiant heat. |
|
| | R2900223 |
|
| | Connect the cable from the front socket to the cable from the engine block heater, or to the branching connector. Take the locking sleeves from the kit and press them in over the joints. Take a clamp from the kit and press it into the hole on the previously installed bracket. Clamp the cable in at the bracket as illustrated.
Caution!
The cable must not be secured to the drive shaft, to the fuel lines, air conditioning (A/C) pipes or brake pipes. Ensure that the cable is not rubbing against any sharp edges and that it is not too close to the turbocharger (TC) or exhaust pipe to prevent damage from radiant heat. |
|
| | Applies to S60 and V70 (00–) |
| | |
| | Applies to the S80 and XC70 |
| | |