| | Preparations at the front of the car |
| | Preparations at the front of the car Applies to cars with manual gearboxes: Turn the ignition key to position “0”. Remove the ignition key from the ignition switch.
Applies to cars with automatic gearboxes: Turn the ignition key to position “0”.
|
| | M8600655 |
|
| | M8600653 |
|
| | Illustration A applies to the V70 Illustration B applies to the S60 and the V70 XC Press in the centre of the six clips until a click is heard. Remove the clips Pull the top edge of the front panel forwards Insert your hand in the inside. Press the four catches along the top edge upwards (applies to the V70, illustration A) or downwards (applies to the S60 and the V70 XC, illustration B).
Use a weatherstrip tool if necessary Pull the top edge of the front grille outward until the catches release.
|
| | M8600597 |
|
| | M8600657 |
|
| | A. Applies to the V70 B. Applies to the S60 and the V70 XC Insert a plastic weatherstrip tool between the front grille and the bumper cover. Carefully pry off the radiator grille along the lower edge. The grille is secured with three catches
Remove the front grille. Place the grille to one side.
|
| | M2501081 |
|
| | |
| | M2000292 |
|
| | |
| | M2501083 |
|
| | |
| | M3501100 |
|
| | Push the rubber seal (1) (on the left inside of the grille) to one side. Take the cable harness (2) from the kit. Position the cable harness in the engine compartment. Route the cable
harness at the left-hand headlamp by the upper edge and through the cut-out in the car body by the rubber seal Push the rubber seal back into place. Ensure that it provides a good seal.
|
| | M8200157 |
|
| | M8600598 |
|
| | A. Applies to the V70 B. Applies to the S60 and the V70 XC |
| | M8600599 |
|
| | |
| | Installing the auxiliary lamps |
| | M8600600 |
|
| | Installing the auxiliary lamps Secure the auxiliary lamp bracket (1) from the kit in the holes (2) for the number plate holder. S60 and V70: Use the lower holes in the bracket.V70 XC: Use
the upper holes in the bracket Drill using a 7mm (9/32") diameter drill bit. Drill the centre of the holes (3). Drill through the bumper cover and the bumper rail (which are positioned differently depending on the
model):
Applies to cars of model year -2004 S60: approximately 37 mm (1.46”) in front of the cover V70: approximately 52 mm (2.05") in front of the cover V70 XC: approximately
51 mm (2.01") in front of the cover
Note!
Hold the drill horizontally. |
Applies to cars from model year 2005- S60: approximately 58 mm (2.28”) in front of the cover V70: approximately 61 mm (2.40") in front of the cover V70 XC: approximately
51 mm (2.01") in front of the cover
Note!
Hold the drill horizontally. |
Remove the screws and the auxiliary lamp bracket.
|
| | D3500968 |
|
| | Drill the holes (1) using a drill bit (P/N 8633152). Drill through the plastic using the thicker section of the drill bit. Drill through the bumper rail (2) using the smaller section of
the drill bit (Ø 7.3 mm (19/64")).
Note!
It is important that the tip of the drill bit meets the hole that was previously drilled into the bumper rail. |
The flat surface of the drill bit must drill out all the plastic up to the bumper rail.
Note!
Hold the drill horizontally. Using a torch, check that there is no plastic swarf in the holes. |
|
| | M8600658 |
|
| | M8601192 |
|
| | Illustration A Applies to cars of model year -2004 Check that there is no plastic in the area (1) on which the spacers will rest Install the two spacers in the holes;S60: Length approximately 40 mm (1.57”) V70: Length approximately 53.5 mm (2.11") V70 XC:
Length approximately 60 mm (2.36")
Note!
The spacers must protrude at different lengths from the bumper cover, depending on the model. S60: approximately 3 mm
(0.12”) out of the bumper cover V70: approximately 1 mm (0.04") out of the bumper cover V70 XC: approximately 9 mm (0.35") out of the bumper cover |
Illustration B Applies to cars from model year 2005- Check that there is no plastic in the area (1) on which the spacers will rest Install the two spacers in the holes;S60: Length approximately 60 mm (2.36”) V70: Length approximately 63.5 mm (2.5") V70 XC:
Length approximately 60 mm (2.36")
Note!
The spacers must protrude at different lengths from the bumper cover, depending on the model. S60: approximately 2 mm
(0.08”) out of the bumper cover V70: approximately 2 mm (0.08") out of the bumper cover V70 XC: approximately 9 mm (0.35") out of the bumper cover |
|
| | M8600659 |
|
| | Applies only to the S60 and the V70: Drill two new holes in the number plate holder as illustrated. |
| | M3501038 |
|
| | Secure the tie straps (1) in the holes in the auxiliary lamp bracket. Do not tighten Install the auxiliary lamp bracket on the bumper using the screws (2) from the kit. Finger tighten. The screws are self-tapping so it may be hard to screw them in.
|
| | M3501039 |
|
| | Insert the two cable ends (1) in the three tie straps (2). Route the wiring as illustrated Adjust the cable lengths for the lamps. Press any excess cable outside the grille back into the grille Tighten the tie straps.
Note!
Tighten the two screws for the auxiliary lamp bracket. |
Install a spacer washer (3) between the auxiliary lamp bracket (4) and the expander nut (5) on both sides Install the number plate. Secure the number plate using the two screws.
|
| | A3500379 |
|
| | Use auxiliary lamps recommended by your Volvo dealer. Remove the screw (1) and cover Press lightly on the lens (2) Position a screwdriver (3) between the insert and lamp housing and pry gently.
|
| | M3501040 |
|
| | |
| | M3501041 |
|
| | |
| | D3500974 |
|
| | |
| | A3500386 |
|
| | |
| | M3501101 |
|
| | Route the previously routed cable harness (1) as illustrated Connect the connector (2) to the existing connector Press the relay (3) into place by the edge of the panel Slacken off the existing screw (4) in the bracket for the air cleaner module. Connect the ground lead. Pull any cable excess through the grille. Secure the excess at the existing wiring
behind the headlamps using the tie straps from the kit Reinstall the air cleaner module and intake pipe.
Note!
Ensure that the wiring does not rub against sharp edges. If the wiring is rubbing, re-secure the wiring. |
|
| | M3702189 |
|
| | Applies to cars of model year -2004 Remove the cover from the fuse holder in the engine compartment. Install a 20A fuse in position 2 (1) Reinstall the cover.
|
| | Installing switches in model year -2004 cars |
| | M8502988 |
|
| | Installing switches in model year -2004 cars |
| | M8503027 |
|
| | |
| | M8503045 |
|
| | Model year -2004 Carefully angle the dashboard environment panel out using a plastic weatherstrip tool so that it is possible to insert a couple of fingers to gain access to the side of the dashboard
environmental panel Remove the dashboard environment panel. Pull the dashboard environment panel downwards while maintaining the same angle. Some force is required because the panel is tightly installed
Disconnect the connectors on the reverse of the dashboard environment panel. Place the dashboard environment panel to one side.
Note!
If any of the outer hooks break off, these must be repaired. See the section dealing with the dashboard in the Workshop manual in VIDA. |
|
| | M8503159 |
|
| | Model year -2004 Remove the cigarette lighter Position the dashboard environmental panel as illustrated Detach the surround (1) by carefully pushing down the three catches (2) in the holes (3). Use a small screwdriver. At the same time pry out the surround using a thin weatherstrip tool.
Starting at the 12 volt socket (4), pry up one corner. The surround is well secured so do not damage any components.
Note!
The surround with three button spaces can be replaced with a
surround with seven button spaces if necessary. This can be purchased separately. |
|
| | Installing switches in model year 2005- cars |
| | M3904985 |
|
| | Installing switches in model year 2005- cars |
| | M3904986 |
|
| | |
| | D8502226 |
|
| | |
| | Finishing work, alignment and adjusting |
| | Finishing work, alignment and adjusting Set the auxiliary lamps for optimal light distribution Tighten the two screws. See point Install protective caps on the screw heads.
|
| | M3000486 |
|
| | |
| | Turn the ignition key to position “II”. Reconnect the battery negative lead Reinstall the floor support in the cargo compartment.
|