| | Applies to cars with twin rear silencers Note!
To facilitate access when tightening the towbar member, the exhaust system must be cut off at the marking according to points 19 and 21. It is important to use this method, otherwise there is a risk of damaging the exhaust system if the silencers are forced down for example. |
|
| | IMG-261524 |
|
| | Note the engine version of the car. Enter VIDA under Engine and suspension, Intake and exhaust system, Silencer and exhaust system, Silencer rear. Order the exhaust clamp for joining the exhaust system.
|
| | |
| | IMG-259683 |
|
| | Preparations Applies to the V70 |
| | IMG-259684 |
|
| | |
| | IMG-259685 |
|
| | IMG-273303 |
|
| | Illustration A Illustration B |
| | IMG-273304 |
|
| | Carefully pull of the ends of the bumper cover from the body on both sides. They are attached with hooks at the upper edge of the ends and at the lower edge of the tail lights. Pull the bumper cover away from the body, it is secured by seven guides at the upper edge of the longer side. If the car is equipped with rear parking assistance, disconnect the connector on the right-hand side of it.
Note!
To prevent damaging the bumper cover, it is recommended to request the assistance of a colleague during this procedure. |
Place the bumper cover on a suitable surface.
|
| | |
| | IMG-259752 |
|
| | |
| | IMG-259753 |
|
| | |
| | IMG-259754 |
|
| | IMG-259755 |
|
| | |
| | IMG-259756 |
|
| | Carefully pull of the bumper cover ends from the body on both sides. They are attached with hooks at the upper edge and front edge of the ends and at the lower edge of the tail lights. Pull the bumper cover away from the body, it is secured by seven guides at the upper edge of the longer side. If the car is equipped with rear parking assistance, disconnect the connector on the right-hand side of it.
Note!
To prevent damaging the bumper cover, it is recommended to request the assistance of a colleague during this procedure. |
|
| | |
| | IMG-261414 |
|
| | Applies to the V70 and the XC70 |
| | IMG-259759 |
|
| | |
| | IMG-259760 |
|
| | |
| | IMG-259761 |
|
| | |
| | IMG-259762 |
|
| | |
| | IMG-259763 |
|
| | |
| | |
| | IMG-260410 |
|
| | Installing the cradle for the towing ball, applies to cars without a spare wheel Note!
Check that there are no cable harnesses on the inside obstructing the hole drilling process. |
Measure and mark out holes for drilling to insert screws for the cradle for the tow ball. Pre-drill using a small drill bit, and drill out the hole to Ø8 mm (5/16"). Deburr the edges of the hole, apply rustproofing agent and remove the drill swarf.
|
| | IMG-226142 |
|
| | |
| | IMG-226143 |
|
| | |
| | Applies to cars with twin rear silencers Note!
Depending on engine version, the car is equipped with one or two rear silencers. Steps 19-36 apply to cars with twin rear silencers |
|
| | IMG-260845 |
|
| | Steps 19-20 apply to cars with AWD Cut the exhaust pipe using the pipe cutter as illustrated. The cutting point is also marked by a small indentation underneath the pipe.
|
| | IMG-260846 |
|
| | |
| | |
| | IMG-260847 |
|
| | Steps 21 apply to cars with 2WD Cut the exhaust pipe using the pipe cutter as illustrated. The cutting point is also marked by a small indentation underneath the pipe.
|
| | IMG-259825 |
|
| | Hint
Get help from a colleague for this procedure. |
|
| | IMG-260849 |
|
| | |
| | IMG-260850 |
|
| | |
| | IMG-260851 |
|
| | |
| | IMG-260852 |
|
| | |
| | IMG-260411 |
|
| | Installing the towing member Check that the contact surfaces inside the side members are clean, if not, clean them opposite where the towing member's side plates shall be tightened. Take the towing member from the kit and insert the two side plates in the holes in the rear edge of the side members.
|
| | IMG-260853 |
|
| | Take the screws and reinforcement bar from the kit. Request the assistance of a colleague and adjust the position of the tow bar as the screws enter the welded nuts of the tow bar.
Note!
Ensure that the reinforcement bar is correctly positioned (see small image). |
Tighten the screws alternately on both sides.
|
| | IMG-261123 |
|
| | Tightening the screw joint Torque tighten the screws to 90 Nm (66.5 lbf.ft.) and angle tighten to 60°. When angle-tightening the joint in confined spaces, a protractor applied to a torque wrench cannot be used. Instead, use the Allen screw's head to determine the angle. Make a mark on the screw head flange (1). Make a second mark (2) in the side member or reinforcement bar. Now tighten the screw so that the screw head marking (1) lines up with the marking (2) on the side member/reinforcement bar. Repeat for all screws.
|
| | IMG-260855 |
|
| | |
| | IMG-261083 |
|
| | |
| | IMG-282943 |
|
| | Installing the exhaust clamp |
| | IMG-282946 |
|
| | |
| | IMG-282963 |
|
| | Request the assistance of a colleague, lift up and reinstall the silencers with exhaust pipe in the exhaust clamp. Refit the mountings for the silencers. Torque tighten the screws to 50 Nm (37 lbf. ft.).
|
| | |
| | IMG-260865 |
|
| | |
| | IMG-282964 |
|
| | Note!
Check that there is no exhaust gas leakage. |
|
| | Applies to cars with single rear silencer Note!
Depending on engine version, the car is equipped with one or two rear silencers. Steps 37-53 apply to cars with a single rear silencer. |
|
| | IMG-259824 |
|
| | Steps 37-53 apply to cars with AWD |
| | IMG-259827 |
|
| | |
| | IMG-260867 |
|
| | |
| | IMG-260868 |
|
| | |
| | IMG-260869 |
|
| | |
| | IMG-260870 |
|
| | Secure a retaining strap between the silencer and the wheel. Secure so that the silencer turns to the side, but not so hard that the exhaust system becomes damaged. Work out the radiated heat shield by rocking the silencer at the same time.
|
| | IMG-260871 |
|
| | |
| | IMG-282965 |
|
| | |
| | IMG-259841 |
|
| | |
| | IMG-260411 |
|
| | Installing the towing member Check that the contact surfaces inside the side members are clean, if not, clean them opposite where the towing member's side plates shall be tightened. Take the towing member from the kit and insert the two side plates in the holes in the rear edge of the side members.
|
| | IMG-259843 |
|
| | Take the screws and reinforcement bar from the kit. Request the assistance of a colleague and adjust the position of the tow bar as the screws enter the welded nuts of the tow bar.
Note!
Ensure that the reinforcement bar is correctly positioned (see small image). |
Tighten the screws alternately on both sides.
|
| | IMG-260854 |
|
| | Tightening the screw joint Torque tighten the screws to 90 Nm (66.5 lbf.ft.) and angle tighten to 60°. When angle-tightening the joint in confined spaces, a protractor applied to a torque wrench cannot be used. Instead, use the Allen screw's head to determine the angle. Make a mark on the screw head flange (1). Make a second mark (2) in the side member or reinforcement bar. Now tighten the screw so that the screw head marking (1) lines up with the marking (2) on the side member/reinforcement bar. Use special tool 9997338. Repeat for all screws.
|
| | IMG-260923 |
|
| | |
| | IMG-260867 |
|
| | |
| | IMG-260924 |
|
| | Check that the mating surfaces in the joint between the exhaust pipes are clean. Take a new gasket and new nuts, tighten the exhaust pipes to each other. Tighten the nuts to 24 Nm (18 lbf.ft.).
|
| | IMG-259871 |
|
| | |
| | IMG-259873 |
|
| | |
| | |
| | IMG-259823 |
|
| | Steps 54-68 apply to cars with 4-, 5-cylinder engines and 2WD |
| | IMG-259827 |
|
| | |
| | |
| | IMG-259836 |
|
| | IMG-259837 |
|
| | IMG-259838 |
|
| | Image A applies to cars with a 4 cylinder diesel engine Image B applies to cars with a 4 cylinder petrol engine Image C applies to cars with a 5 cylinder diesel engine Remove the nuts in the joint behind/in front of the front silencer, and separate the joint.
Note!
Always use a new gasket and nuts when installing. |
Secure the silencer to prevent damaging the boot at the catalytic converter.
|
| | IMG-259829 |
|
| | |
| | IMG-260925 |
|
| | |
| | IMG-282965 |
|
| | |
| | IMG-259841 |
|
| | |
| | |
| | IMG-260411 |
|
| | Installing the towing member Check that the contact surfaces inside the side members are clean, if not, clean them opposite where the towing member's side plates shall be tightened. Take the towing member from the kit and insert the two side plates in the holes in the rear edge of the side members.
|
| | IMG-259843 |
|
| | Take the screws and reinforcement bar from the kit. Request the assistance of a colleague and adjust the position of the tow bar as the screws enter the welded nuts of the tow bar.
Note!
Ensure that the reinforcement bar is correctly positioned (see small image). |
Hint
The silencer must be depressed for the screws and reinforcement bar to be installed and tightened correctly. |
Tighten the screws alternately on both sides.
|
| | IMG-260854 |
|
| | Tightening the screw joint Torque tighten the screws to 90 Nm (66.5 lbf.ft.) and angle tighten to 60°.When angle-tightening the joint in confined spaces, a protractor applied to a torque wrench cannot be used. Instead, use the Allen screw's head to determine the angle. Make a mark on the screw head flange (1). Make a second mark (2) in the side member or reinforcement bar. Now tighten the screw so that the screw head marking (1) lines up with the marking (2) on the side member/reinforcement bar. Use special tool 9997338. Repeat for all screws.
|
| | |
| | IMG-260929 |
|
| | |
| | IMG-259865 |
|
| | |
| | |
| | IMG-259866 |
|
| | IMG-259867 |
|
| | IMG-259868 |
|
| | Image A applies to cars with a 4 cylinder diesel engine Image B applies to cars with a 4 cylinder petrol engine Image C applies to cars with a 5 cylinder diesel engine Check that the mating surfaces in the joint between the exhaust pipes are clean. Take a new gasket and new nuts from the kit and tighten the exhaust pipes to each other. Tighten the nuts to 24 Nm (18 lbf.ft.).
|
| | IMG-259871 |
|
| | |
| | IMG-259874 |
|
| | |
| | |
| | IMG-259875 |
|
| | |
| | IMG-259876 |
|
| | IMG-282983 |
|
| | Illustration A Illustration B |
| | IMG-282984 |
|
| | |
| | IMG-260746 |
|
| | |
| | IMG-259881 |
|
| | |
| | |
| | IMG-260443 |
|
| | IMG-260444 |
|
| | Cutting out the bumper cover Illustration A applies to the V70 Illustration B applies to the XC70 Apply tape to the outside of the bumper cover, opposite the markings on the inside. This is done to protect the paint from the saw when cutting out the cut-out for the towbar. Cut according to the markings.
Note!
Do not damage the painted surface of the bumper cover. Cut so that the raised edge on the inside remains. The raised edge marks the cut-out. |
Remove the tape. Smooth off the sawn edges with a fine toothed file. Install the tow hitch connector with cable harness according to the appropriate installation instructions.
|
| | IMG-326103 |
|
| | Applies to the V70 with R-design Saw out the lower section of the bumper casing according to the markings. Remove the shaded area. Tape the outside to prevent the saw foot from damaging the paint.
Note!
Do not damage the paintwork of the bumper cover. |
Smooth off the sawn edges with a fine toothed file.
|
| | IMG-260747 |
|
| | Applies to the V70 Connect the connector to the rear park assistance if applicable, and reinstall the bumper cover. Ensure that all hooks and guides engage.
Note!
To prevent damaging the bumper cover, it is recommended to request the assistance of a colleague during this procedure. |
Tighten the screw at the front edge of the ends.
|
| | IMG-259886 |
|
| | IMG-259887 |
|
| | |
| | IMG-260748 |
|
| | |
| | IMG-259889 |
|
| | Check that the end pipes for the silencer(s) are correctly centered in the bumper cover cut-out. If necessary/applicable, make adjustments at the cutting point, mountings at the rear silencer or at the joint between the silencer.
|
| | |
| | IMG-260749 |
|
| | |
| | IMG-259891 |
|
| | IMG-259892 |
|
| | |
| | IMG-260750 |
|
| | |
| | IMG-259894 |
|
| | Check that the end pipes for the silencer(s) are correctly centered in the bumper cover cut-out. If necessary/applicable, make adjustments at the cutting point, mountings at the rear silencer or at the joint between the silencer.
|
| | |
| | IMG-226147 |
|
| | IMG-226145 |
|
| | Storing the towball Applies to cars without spare wheel Illustrations A and B Remove the bag from the kit, put the towball inside and tie it up.
Note!
The towbar must be positioned in the holder as indicated in Illustration B. |
Wind the long strap twice around the bag and tighten firmly.
|
| | IMG-226150 |
|
| | IMG-226148 |
|
| | Applies to cars with spare wheel Illustrations A and B Remove the bag from the kit, put the towball inside and tie it up.
Note!
The towbar must be positioned as in Illustration B. |
Wind the long strap twice around the bag and once around the wheel and tighten firmly.
|
| | IMG-260445 |
|
| | Take the label from the kit and affix it firmly to the underside of the storage compartment, as illustrated. In addition, use staples in the four corners of the labels.
|
| | |
| | IMG-261415 |
|
| | |
| | |
| | IMG-226909 |
|
| | Protective cover Installation |
| | IMG-227105 |
|
| | |
| | IMG-260447 |
|
| | |