| | |
| | IMG-331668 |
|
| | |
| | J8504532 |
|
| | |
| | IMG-239762 |
|
| | |
| | IMG-240082 |
|
| | |
| | IMG-244221 |
|
| | |
| | J8803318 |
|
| | Remove the rubber mat from the glovebox. Remove the five screws in the opening. Pull the glovebox straight back in the vehicle in order to release the two hidden clips in the top edge. Remove the outer section of the glovebox.
|
| | IMG-222669 |
|
| | |
| | IMG-239763 |
|
| | |
| | J8504871 |
|
| | |
| | J8504893 |
|
| | Detach the surround around the display and media player. Press in the catch in one of the upper corners of the surround using a small screwdriver. Carefully pry off the surround on the same side using a weatherstrip tool.
Note!
Do not damage the panel and dashboard. |
Repeat the operation on the other side.
Hint
If the panel is difficult to remove, press the panel on both sides again and repeat the procedure starting at the other side. |
Fold the surround backwards. Remove by pulling upwards.
|
| | J8504534 |
|
| | |
| | IMG-263205 |
|
| | |
| | IMG-270743 |
|
| | |
| | IMG-263584 |
|
| | |
| | IMG-263949 |
|
| | |
| | IMG-270744 |
|
| | |
| | IMG-263586 |
|
| | IMG-263208 |
|
| | Illustration A Illustration B |
| | IMG-263209 |
|
| | |
| | IMG-263588 |
|
| | Applies to cars with manual gearbox Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.
|
| | IMG-240085 |
|
| | |
| | J3905272 |
|
| | |
| | J3904501 |
|
| | |
| | IMG-276017 |
|
| | Applies to cars with internal amplifier Remove cable harness A from the kit.
Applies to cars with external amplifier Remove cable harness B from the kit.
Applies to all models Connect the gray connector (2) in the new cable harness to the gray connector (3) which was detached from the media player. Take a 700 mm piece of foam tape and cut into three pieces of the same length. Tape one piece around connectors (2) and (3). Position these to the left, in the opening so that they are not in the way when installing the media player. Connect the gray connector (1) in the new cable harness to the corresponding socket in the media player. Pull the cable harness with the connectors down to the right-hand side of the center console. Plug the remaining connectors which where detached into the media player. Reinstall the media player and secure it.
|
| | Installing the control panel |
| | IMG-331708 |
|
| | Installing the control panel Clean the area on the centre console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Dry with care, do not rub. Allow to dry.
Note!
In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent. |
|
| | IMG-331669 |
|
| | IMG-331670 |
|
| | |
| | IMG-331707 |
|
| | |
| | IMG-240872 |
|
| | Press the cable securely into the compartment that is in the joint between the front and rear side of the center console. Stop level with the lower edge of the display opening. Reinstall the center console, connect the green connector and install the screws.
Applies to cars with manual gearbox Install the gear selector boot in the center console starting at the rear edge.
|
| | IMG-256723 |
|
| | |
| | Installing the microphone |
| | IMG-253963 |
|
| | Installing the microphone |
| | IMG-274304 |
|
| | |
| | J8504996 |
|
| | Pull off the driver's weather strip at the A-post and dashboard. Pull off the panel from the A-pillar. The panel is secured by three clips. Unhook the safety clip. Lift the panel upwards and inwards in the vehicle. Remove the panel.
|
| | IMG-253982 |
|
| | |
| | IMG-253984 |
|
| | |
| | IMG-253985 |
|
| | Take two 700 mm pieces of foam tape from the kit. Cut one piece of foam tape in the middle. Tape one long and one short piece of foam tape on the microphone cable starting 70 mm from the microphone.
|
| | IMG-253986 |
|
| | |
| | IMG-253989 |
|
| | |
| | IMG-274305 |
|
| | Make a mark on the foam tape affixed to the cable 230 mm from the microphone. Use a cable tie to fasten the cable at the mark at the existing connector. Install the three trim screws.
|
| | IMG-253991 |
|
| | |
| | IMG-282895 |
|
| | Clean the microphone and roof panel in the area illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Dry with care, do not rub. Allow to dry.
Note!
In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent. |
|
| | IMG-253993 |
|
| | |
| | IMG-253994 |
|
| | Warning!
Make sure that the routing of the microphone cable does not interfere with the function of the inflatable curtain. |
|
| | Installing the control module |
| | IMG-250303 |
|
| | Installing the control module |
| | IMG-256724 |
|
| | |
| | IMG-256725 |
|
| | |
| | IMG-250923 |
|
| | |
| | J8504868 |
|
| | |
| | IMG-256726 |
|
| | |
| | IMG-256727 |
|
| | Fold aside the cable harnesses (1) so that they do not end up between the control module and floor mat. Route the control module's cable harness under the cable harnesses (2) and on toward the tunnel console.
|
| | |
| | IMG-239780 |
|
| | |
| | IMG-239782 |
|
| | Applies to cars with internal amplifier Take the relay and two thick pieces of foam tape from the kit. Connect the connectors from cable harness A to the relay. Tape the foam tape pieces around the relay.
|
| | IMG-239783 |
|
| | Applies to cars with internal amplifier Place the relay between the carpet and the climate control unit as illustrated.
|
| | IMG-239778 |
|
| | Applies to cars with internal amplifier 1. Connect cable harness A to the cable from the control module.
Applies to cars with external amplifier 1. Connect cable harness B to the cable from the control module.
|
| | IMG-239781 |
|
| | |
| | IMG-248570 |
|
| | Applies to cars with external amplifier Also secure the cable harness B, that is to be later routed back to the external amplifier.
|
| | IMG-270744 |
|
| | Reinstall: gear lever gaiter, starting at the trailing edge. and slide the tunnel console forward so that the lugs secure it. At the same time align the floor carpet on the right and left-hand sides. the two screws at the front edge of the tunnel console. the panel at the parking brake. the two screws and the cover under the armrest. front storage compartment inside of the center console. and connect the display unit. the surround for the display.
|
| | J8504708 |
|
| | Steps 56-75 apply to cars with external amplifier. Grasp the upper edge of the right-hand side cushion. Pull the side cushion forward so that the clip on the reverse releases. Slide the side cushion up. Remove the side cushion. Repeat the operation on the other side.
|
| | J8504585 |
|
| | Pull off the rubber strip at the rear of the opening for the right-hand rear door. Carefully pry off the lower panel on the C-post on the right-hand side. Carefully pry at the top edge. Use a plastic weatherstrip tool. Pull the panel on the C-post so that the two upper clips release. Then continue down until the last two clips release. Remove the panel on the C-post.
|
| | J8504733 |
|
| | |
| | J8504735 |
|
| | Pull off the rubber moldings at the rear edge of the right-hand front door and at the front edge of the right-hand rear door. This releases the lower panel on the B-pillar. Pull the bottom edge of the lower panel on the B-pillar until the two bottom clips release.
|
| | IMG-240925 |
|
| | |
| | J8504575 |
|
| | |
| | IMG-240926 |
|
| | Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips on the short side release. Pull up the sill trim panel so the remaining six clips release. Remove the panel. Detach the rubber strip where it covers the left and right-hand side panel in the tailgate opening.
|
| | IMG-240927 |
|
| | |
| | J8504570 |
|
| | Fold out the load securing eyelets. Insert a scriber with an angled tip into the holes in the top of the covers (1). Turn the scriber so that the tip engages the reverse of the cover. Pull the covers off. Remove the screws in the load securing eyelets. Remove the screw (2). Pull off the side panel at the top so that the two clips at the rear/bottom of the side window and the clip at the bottom of the D-post release. Disconnect the connector for the 12V socket, if present. This is carried out on the left-hand side on right-hand drive vehicles.
|
| | J8504553 |
|
| | |
| | J8504552 |
|
| | |
| | J8504554 |
|
| | Unscrew the two external clips at the front edge/bottom edge of the sill trim panel on the tailgate. Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips in that end release. Pull up the sill trim panel at the other end so that the remaining two clips release. Remove the sill trim panel. Detach the rubber strip where it covers the right-hand side panel in the boot opening.
|
| | J8504584 |
|
| | IMG-240928 |
|
| | Illustrations A and B Remove the four clips (1), in illustration A, holding the side panel in the bodywork. Unhook the front edge of the parcel shelf panel at the mounting (2), in illustration A. Pull the side panel away from the parcel shelf panel and the panel on the C-post. Unhook the side panel from the mounting (3), in illustration B, on the underneath of the parcel shelf. Disconnect the connector for the 12V socket, if present. Unhook the side panel from the load securing eyelets (4), in illustration A. Remove the side panel. This is carried out on the left-hand side on right-hand drive vehicles.
|
| | IMG-243266 |
|
| | Applies to the S40 and V50 Route the cable B inside the floor carpets, the lower B-post panel and the insulation panels, back to the rear edge of the right-hand rear wheel arch. Route the cable along the existing cable harnesses in the cargo compartment.
Note!
Ensure that the cable is positioned so that there is no risk of it catching or rubbing. |
|
| | IMG-240929 |
|
| | Applies to left hand drive S40 and V50 Continue routing the cable harness to the amplifier. Position the cable harness at the existing cable harness to the side and at the rear edge of the cargo compartment, all the way from the right-hand wheel arch to the amplifier. Take a short tie strap from the kit and secure the cable harness at the existing cable harness.
|
| | J8504639 |
|
| | |
| | IMG-240930 |
|
| | |
| | IMG-240931 |
|
| | Connect cable harness C from the kit to the amplifier as follows: Connector (1) that was disconnected from the amplifier is connected to the female connector (2) on the adapter cable. plug connector (3) on the adapter cable into the amplifier. Tape one section of the cut piece of foam tape around connectors 1 and 2. Secure the excess cable using one of the cut up parts of foam tape and two short tie straps, on the existing cable harness of the vehicle.
|
| | IMG-239782 |
|
| | Applies to the S40 and V50 Take the relay from the kit. Connect the connectors from cable harness B and C to the relay. Tape two thick pieces of foam tape around the relay.
|
| | IMG-240932 |
|
| | |
| | |
| | IMG-231504 |
|
| | Finishing work Applies to all models |
| | IMG-228142 |
|
| | Dashboard Reinstall: the lower vent. the sound proofing. the rear section of the glovebox by guiding it in diagonally inside the center console and then straight forward. The rear section must be positioned on the outside of the remaining inner section. Remove the tape. the clip for the vent on the glovebox. the panel on the dashboard end face. the pillar panel. the door's weatherstrip at the A-pillar. the panel above the center console. Check that the cable to the control panel is not pinched.
Cargo compartment Reinstall: the side panels. the screws in the load securing eyes. Tightening torque 24 Nm (18 lbf.ft.) (applies to V50). the sill trim panel for the tailgate. the upper floor support if applicable (applies to the S40). the rubber strips in the cargo compartment opening. the cargo compartment carpeting.
Passenger compartment |
| | IMG-331671 |
|
| | Carry out a function test as follows: Turn the ignition key to position I. Turn on the radio. Check that the control panel for Bluetooth lights up. Press the button (1) in the middle of the control panel. The radio should mute and a voice should be heard. Press the button (2). The voice should stop and the radio sound should return.
|