| | |
| | IMG-245980 |
|
| | Note!
Wait at least three minutes before unplugging the connectors or removing other electrical equipment. |
|
| | IMG-217765 |
|
| | |
| | IMG-217766 |
|
| | |
| | IMG-217767 |
|
| | Undo the front screw in the mounting for the centre console. Take the bracket for the passenger compartment socket from the kit. Tighten it with the previously removed screw. Position it so that it is straight and torque tighten the screw to 24 Nm (18 lbf.ft.).
|
| | IMG-217768 |
|
| | |
| | IMG-217769 |
|
| | |
| | IMG-217770 |
|
| | Press in the locking sleeve on the passenger compartment socket. Slide the locking sleeve as far as possible on the connection for the passenger compartment socket. Take a carpet knife and cut a slit in the carpet just in front of the locking sleeve. Make the cut as long as the diameter of the locking sleeve. Remove the passenger compartment connector socket from the bracket and fold the carpet to one side.
Note!
Do not damage any wiring and hoses under the carpet. |
|
| | IMG-231309 |
|
| | |
| | IMG-231821 |
|
| | |
| | IMG-300204 |
|
| | |
| | IMG-296703 |
|
| | Carefully pry up the four catches on the lock sleeve with a small screwdriver and pull it backwards. Unplug the connector from the heater's socket. Carefully cut loose the locking sleeve from the cable. New locking sleeve is found in the kit.
|
| | IMG-296704 |
|
| | Cut off the strip clamp and loosen the clip for the cable from the flange in the engine block. Remove the heat shield from the cable, it is going to be used again.
|
| | IMG-296705 |
|
| | IMG-296706 |
|
| | |
| | IMG-296707 |
|
| | Get the branching connector, holder, screw, washer, and nut from the kit. Assemble and tighten down.
|
| | D3601932 |
|
| | Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-296708 |
|
| | Get the two splicing cables and the small locking sleeves from the kit. Press the cables into the branching connector. Press the locking sleeves over the joints.
|
| | IMG-296723 |
|
| | Note!
Make sure that the branching connector faces so that the shorter cable is in the front position. |
Get a hose clamp from the kit and tighten down the branching connector on the steering gear in the position as shown. Press the cable from the front socket securely in the branching connector and press a locking sleeve from the kit over the joint.
|
| | IMG-296724 |
|
| | |
| | IMG-296725 |
|
| | |
| | IMG-300205 |
|
| | |
| | D3601932 |
|
| | Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-296726 |
|
| | |
| | IMG-300206 |
|
| | |
| | IMG-296727 |
|
| | |
| | IMG-296743 |
|
| | |
| | IMG-231839 |
|
| | |
| | IMG-296823 |
|
| | Lubricate the rubber bushing with low temperature in order to make it easier to install the cable and rubber bushing in the hole in the firewall. Thread the rubber grommet onto the cable. Adjust the length of the cable to the rubber bushing's placement in the firewall's hole.
Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-300207 |
|
| | Route the remaining cable (to the passenger compartment connector) from the branching connector to the right end of the power steering. Press on a double clamp from the kit on the front pipe and fasten the cable.
|
| | IMG-296824 |
|
| | |
| | IMG-231335 |
|
| | |
| | IMG-217776 |
|
| | IMG-217777 |
|
| | Illustration A Illustration B Route the cable from the engine compartment through the hole in the carpet. Grease the O-ring with low temperature grease (part no. 1161427). Connect the cable to the passenger compartment connector socket. Press a locking sleeve (from the kit) over the joint. Fold the carpet back into position and install the passenger compartment connector using both the screws.
Note!
Ensure that no grease gets onto the connector surfaces. |
|
| | IMG-234260 |
|
| | |