| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-394535 |
|
| | |
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-411070 |
|
| | |
| | IMG-424855 |
|
| | |
| | IMG-414614 |
|
| | |
| | IMG-414995 |
|
| | Fold marked part aside. Remove the screw. Tightening torque: Seat belt guide, to Bracket
, 4.4 Nm
|
| | IMG-415046 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-415047 |
|
| | Remove the panel. Use hands only. |
| | IMG-415049 |
|
| | Release the catch. Remove the marked part. |
| | IMG-418525 |
|
| | Remove the screw. Tightening torque: Cargo anchor, to body
, 13 Nm
|
| | IMG-425211 |
|
| | Remove the screw. Tightening torque: Safety belt lower anchor to body (rear)
, 40 Nm
|
| | IMG-407110 |
|
| | |
| | IMG-414611 |
|
| | |
| | IMG-415830 |
|
| | Repeat on the other side. |
| | IMG-415831 |
|
| | Remove the screw. Tightening torque: M6
, 10 Nm
Repeat on the other side. |
| | IMG-425191 |
|
| | Lift the marked component up |
| | IMG-425125 |
|
| | |
| | IMG-425190 |
|
| | |
| | IMG-416087 |
|
| | |
| | Vehicles with keyless entry |
| | IMG-424841 |
|
| | Release the catch. Loosen the component indicated. Do not remove it. |
| | |
| | IMG-415835 |
|
| | |
| | IMG-416089 |
|
| | |
| | IMG-418545 |
|
| | Remove the panel. Disconnect any connector(s). |
| | IMG-425929 |
|
| | Disconnect the connectors. |
| | IMG-423455 |
|
| | |
| | IMG-425937 |
|
| | Remove the nuts. Remove the marked part. |
| | IMG-423458 |
|
| | Remove the screws. Remove the marked part. The part is not to be reused. |
| | |
| | IMG-423459 |
|
| | |
| | IMG-425939 |
|
| | Place the component where indicated in the graphic. Install the nuts |
| | IMG-423530 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423030 |
|
| | Adjust the component to a horizontal position. |
| | IMG-423329 |
|
| | Position/route the cable as illustrated. Connect the connector. |
| | IMG-425927 |
|
| | |
| | IMG-425945 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-425947 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-425948 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-425513 |
|
| | Remove the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | IMG-423576 |
|
| | |
| | IMG-416273 |
|
| | Remove the nut. Fold marked part aside. |
| | IMG-416275 |
|
| | Release the catches. Fold marked part aside. |
| | IMG-389347 |
|
| | |
| | Vehicles with Alcohol Analysing Start Inhibitor |
| | IMG-425031 |
|
| | |
| | IMG-425032 |
|
| | Use special tool: T9512631, Terminal removal tool (Color code: Brown)
|
| | IMG-425034 |
|
| | Note! On some vehicles the Red/Yellow wire might be only Red. |
|
| | IMG-425035 |
|
| | Remove the terminal. Use the wire only. |
| | IMG-425239 |
|
| | |
| | IMG-425040 |
|
| | Use special tool: T9512620, Stripping tool (for wiring)
|
| | IMG-425039 |
|
| | |
| | IMG-425037 |
|
| | |
| | IMG-425049 |
|
| | Use special tool: T9512785, Crimping tool (included in 9512669)
|
| | IMG-425051 |
|
| | Caution! Make sure that the surrounding components are protected from heat. |
Use special tool: T9512777, Hot-air gun
|
| | |
| | IMG-423829 |
|
| | Connect the prerouted cable. |
| | IMG-389348 |
|
| | Reinstall the removed part. |
| | IMG-423830 |
|
| | Install the cable. Use a cable tie |
| | IMG-416277 |
|
| | Reinstall the removed part. |
| | IMG-422785 |
|
| | Install component that comes with the accessory kit. |
| | IMG-423477 |
|
| | Position/route the cables as illustrated. Install the cables. Use a cable tie |
| | IMG-424621 |
|
| | Connect the prerouted cables. BK = Black RD = Red |
| | IMG-424623 |
|
| | Depress the secondary lock. |
| | IMG-422801 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-423586 |
|
| | |
| | |
| | IMG-423587 |
|
| | |
| | IMG-423588 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | |
| | IMG-423884 |
|
| | |
| | IMG-423828 |
|
| | |
| | IMG-423826 |
|
| | Connect the cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423887 |
|
| | Reinstall the removed part. |
| | |
| | IMG-423879 |
|
| | Note! Position the template so that its surfaces are aligned against the panel. |
|
| | IMG-423836 |
|
| | |
| | IMG-423840 |
|
| | Make a hole, using the tool indicated. |
| | IMG-423849 |
|
| | |
| | IMG-423881 |
|
| | Caution! The decal must face upward. |
|
| | IMG-423880 |
|
| | Install the nut. Tighten the nut. Use hands only. |
| | IMG-422988 |
|
| | Connect the prerouted cable. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | IMG-422420 |
|
| | Place the manual for this accessory in a suitable location in the car. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |