| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400004 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
There may be parts in the accessories kit that are not needed for this installation. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-394535 |
|
| | |
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-419056 |
|
| | |
| | IMG-424855 |
|
| | |
| | IMG-423269 |
|
| | |
| | IMG-423270 |
|
| | Fold marked part aside. Remove the screw. Tightening torque: Seat belt guide, to Bracket
, 4.4 Nm
|
| | IMG-419062 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-423275 |
|
| | Remove the panel. Use hands only. |
| | IMG-423279 |
|
| | Release the catch. Remove the marked part. |
| | IMG-423281 |
|
| | Remove the panel. Use hands only. |
| | IMG-423295 |
|
| | |
| | IMG-423296 |
|
| | |
| | IMG-419067 |
|
| | Remove the screw. Tightening torque: Cargo anchor, to body
, 13 Nm
|
| | IMG-425079 |
|
| | Remove the screw. Tightening torque: Safety belt lower anchor to body (rear)
, 40 Nm
|
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | IMG-407110 |
|
| | |
| | IMG-414611 |
|
| | |
| | IMG-415830 |
|
| | Repeat on the other side. |
| | IMG-415831 |
|
| | Remove the screw. Tightening torque: M6
, 10 Nm
Repeat on the other side. |
| | IMG-425191 |
|
| | Lift the marked component up |
| | IMG-425078 |
|
| | Release the lock. Remove the marked part. |
| | IMG-425190 |
|
| | |
| | IMG-416087 |
|
| | |
| | Vehicles with keyless entry |
| | IMG-424841 |
|
| | Release the catch. Loosen the component indicated. Do not remove it. |
| | |
| | IMG-415835 |
|
| | |
| | IMG-416089 |
|
| | |
| | IMG-419165 |
|
| | Remove the panel. Disconnect any connector(s). |
| | IMG-423266 |
|
| | |
| | IMG-423298 |
|
| | |
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | IMG-400005 |
|
| | Replace Fixed side windows according to service information in VIDA: Information/ Repair/ Removal, replacement, installation/ 8 Body and interior/ 84 Exterior trim, glass, weatherstrips/ 844 glass for side doors and window/ Fixed side window |
| | IMG-412242 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414575 |
|
| | |
| | IMG-414580 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414585 |
|
| | Remove the screws. Remove the panel. |
| | IMG-423283 |
|
| | Release the lock. Repeat on the other side. Remove the marked part. |
| | IMG-414483 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-423671 |
|
| | |
| | IMG-397280 |
|
| | |
| | IMG-397244 |
|
| | |
| | IMG-397247 |
|
| | |
| | IMG-412247 |
|
| | Note! Perform the procedure one side at a time. |
Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
Disconnect the connector. |
| | IMG-414590 |
|
| | |
| | IMG-422856 |
|
| | Disconnect the connector. |
| | IMG-422857 |
|
| | Remove the connector from its attachment. |
| | IMG-422858 |
|
| | |
| | IMG-422861 |
|
| | |
| | IMG-422871 |
|
| | |
| | IMG-422872 |
|
| | Disconnect the connector. |
| | IMG-422873 |
|
| | |
| | IMG-422874 |
|
| | |
| | Cars with automatic transmissions |
| | IMG-410487 |
|
| | |
| | IMG-383728 |
|
| | Use special tool: T9512943, L-hook
|
| | Cars with manual transmissions |
| | IMG-422900 |
|
| | Use special tool: T9997077, Jimmy bar
|
| | IMG-422901 |
|
| | Use special tool: T9997077, Jimmy bar
|
| | IMG-425187 |
|
| | Release the locks. Loosen the marked detail/details. |
| | |
| | IMG-422902 |
|
| | |
| | IMG-422903 |
|
| | |
| | IMG-422937 |
|
| | |
| | IMG-422941 |
|
| | |
| | IMG-422943 |
|
| | Disconnect the connectors. |
| | IMG-422946 |
|
| | Caution! Make sure to protect adjacent surfaces or components. |
|
| | IMG-422936 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-383939 |
|
| | Disconnect the connectors. |
| | IMG-423288 |
|
| | Caution! Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
| | IMG-423289 |
|
| | |
| | IMG-423537 |
|
| | |
| | |
| | IMG-423013 |
|
| | |
| | IMG-423536 |
|
| | Place the component where indicated in the graphic. Install the nuts |
| | IMG-423530 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423030 |
|
| | Adjust the component to a horizontal position. |
| | IMG-423329 |
|
| | Position/route the cable as illustrated. Connect the connector. |
| | IMG-423327 |
|
| | |
| | IMG-423754 |
|
| | Position/route the cables as illustrated. Install the cables. Use a cable tie |
| | IMG-423630 |
|
| | Disconnect the connector. |
| | |
| | IMG-423757 |
|
| | Connect the prerouted cables. |
| | |
| | IMG-424609 |
|
| | |
| | IMG-424367 |
|
| | Depress the secondary lock. |
| | IMG-423757 |
|
| | Connect the prerouted cables. |
| | |
| | IMG-423759 |
|
| | |
| | IMG-423760 |
|
| | Attach the connector to the wiring harness. Use a cable tie |
| | IMG-424157 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-424232 |
|
| | Route the wires adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-424235 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-423576 |
|
| | |
| | IMG-416273 |
|
| | Remove the nut. Fold marked part aside. |
| | IMG-416275 |
|
| | Release the catches. Fold marked part aside. |
| | IMG-389347 |
|
| | |
| | Vehicles with Alcohol Analysing Start Inhibitor |
| | IMG-425031 |
|
| | |
| | IMG-425032 |
|
| | Use special tool: T9512631, Terminal removal tool (Color code: Brown)
|
| | IMG-425034 |
|
| | Note! On some vehicles the Red/Yellow wire might be only Red. |
|
| | IMG-425035 |
|
| | |
| | IMG-425038 |
|
| | |
| | IMG-425040 |
|
| | Use special tool: T9512620, Stripping tool (for wiring)
|
| | IMG-425039 |
|
| | |
| | IMG-425037 |
|
| | |
| | IMG-425049 |
|
| | Use special tool: T9512785, Crimping tool (included in 9512669)
|
| | IMG-425051 |
|
| | Use special tool: T9512777, Hot-air gun
|
| | |
| | IMG-422621 |
|
| | Connect the prerouted cable. |
| | IMG-389348 |
|
| | Reinstall the removed part. |
| | IMG-422622 |
|
| | Install the cable. Use a cable tie |
| | IMG-416277 |
|
| | Reinstall the removed part. |
| | IMG-422819 |
|
| | Position/route the cables as illustrated. Install the cables. Use a cable tie |
| | IMG-424621 |
|
| | Connect the prerouted cables. BK = Black RD = Red |
| | IMG-424623 |
|
| | Depress the secondary lock. |
| | IMG-422801 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-423586 |
|
| | |
| | |
| | IMG-423587 |
|
| | |
| | IMG-423588 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | |
| | IMG-423884 |
|
| | |
| | IMG-423828 |
|
| | |
| | IMG-423826 |
|
| | Connect the cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423887 |
|
| | Reinstall the removed part. |
| | |
| | IMG-423496 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
Connect the connector. Position/route the cable as illustrated. Use tape |
| | IMG-423385 |
|
| | Position/route the cable as illustrated. Use tape |
| | IMG-423386 |
|
| | Position/route the cable as illustrated. Use tape |
| | IMG-423763 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-423895 |
|
| | Connect the prerouted cable. Connect the connector. |
| | IMG-423497 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
Connect the connector. Route the wire adjacent to existing wirings. Use tape |
| | IMG-423666 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-423801 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-424233 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-423805 |
|
| | Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-423435 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-423910 |
|
| | Connect the prerouted cable. Connect the connector. |
| | IMG-423485 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-423590 |
|
| | Position/route the cable as illustrated. |
| | IMG-422822 |
|
| | Position/route the cable as illustrated. |
| | IMG-421024 |
|
| | |
| | IMG-422825 |
|
| | Position/route the cable as illustrated. |
| | IMG-423062 |
|
| | Install the cable. Use a cable tie |
| | IMG-423075 |
|
| | Install the cable. Use a cable tie |
| | IMG-422980 |
|
| | Position/route the cable as illustrated. |
| | IMG-422981 |
|
| | |
| | IMG-423076 |
|
| | Tear off the excess foam tape. |
| | IMG-414040 |
|
| | |
| | |
| | IMG-414045 |
|
| | |
| | IMG-422951 |
|
| | Reinstall the removed part. Reinstall the screws. |
| | IMG-422950 |
|
| | |
| | IMG-423077 |
|
| | Install the wiring harness. Use a cable tie |
| | |
| | IMG-422785 |
|
| | Install component that comes with the accessory kit. |
| | IMG-423879 |
|
| | Note! Position the template so that its surfaces are aligned against the panel. |
|
| | IMG-423836 |
|
| | |
| | IMG-423840 |
|
| | Make a hole, using the tool indicated. |
| | IMG-423849 |
|
| | |
| | IMG-423881 |
|
| | Caution! The decal must face upward. |
|
| | IMG-423880 |
|
| | Install the nut. Tighten the nut. Use hands only. |
| | IMG-422988 |
|
| | Connect the prerouted cable. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-424469 |
|
| | |
| | IMG-424470 |
|
| | Check for correct operation. |
| | IMG-422420 |
|
| | Place the manual for this accessory in a suitable location in the car. |