| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | There may be parts in the accessories kit that are not needed for this installation. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-497538 |
|
| | There may be parts in the accessories kit that are not needed for this installation. |
| | Disconnecting the battery |
| | IMG-478933 |
|
| | |
| | IMG-480317 |
|
| | |
| | IMG-473637 |
|
| | |
| | IMG-473659 |
|
| | Remove the clips. Remove the marked part. |
| | IMG-473722 |
|
| | Remove the battery's negative cable. |
| | |
| | IMG-498376 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
| | IMG-498377 |
|
| | |
| | IMG-498378 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-498379 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
| | |
| | IMG-498450 |
|
| | Caution! Make sure that the surface is clean and free of foreign material. |
Clean the marked area. Use: , Isopropanol
|
| | IMG-499117 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-499118 |
|
| | Lift approximately 2 mm. Remove the marked part.
|
| | IMG-499401 |
|
| | |
| | IMG-499408 |
|
| | |
| | IMG-499410 |
|
| | Apply tape. Use: , Masking tape
|
| | IMG-499414 |
|
| | Apply a thin and even layer. Use: 1161823, Activator
|
| | IMG-499415 |
|
| | |
| | IMG-499105 |
|
| | Remove the protective film. |
| | IMG-499417 |
|
| | Note! Press the component to remove any air bubbles between the window and the component. |
Allow to dry for at least 20 minutes. |
| | |
| | IMG-431485 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-431600 |
|
| | |
| | IMG-490420 |
|
| | |
| | IMG-491220 |
|
| | |
| | IMG-491223 |
|
| | Remove the screw. Tightening torque: Panel A-pillar
, 4.5 Nm
|
| | IMG-491227 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-491237 |
|
| | |
| | IMG-430326 |
|
| | Disconnect any connector(s). Remove the marked part. |
| | IMG-431610 |
|
| | Caution! Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
| | IMG-479002 |
|
| | |
| | IMG-479311 |
|
| | Remove the part carefully Repeat the steps when removing on opposite side. |
| | IMG-479001 |
|
| | |
| | IMG-479023 |
|
| | Remove the marked part. Remove the screw. Tightening torque: Panel, to C pillar
, 4.5 Nm
|
| | IMG-479026 |
|
| | The graphic shows the back of the component. |
| | IMG-479028 |
|
| | |
| | IMG-479029 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-479032 |
|
| | |
| | IMG-479043 |
|
| | |
| | IMG-431455 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-431460 |
|
| | |
| | IMG-431471 |
|
| | |
| | IMG-479303 |
|
| | |
| | IMG-498375 |
|
| | |
| | IMG-498481 |
|
| | Caution! Take extra care not to crease the headliner. |
Loosen the marked details. Fold marked part aside. |
| | IMG-498373 |
|
| | Loosen the marked detail. |
| | IMG-498374 |
|
| | Release the catches. Loosen the marked details. |
| | |
| | IMG-498397 |
|
| | Caution! Make sure that the surface is clean and free of foreign material. |
Clean the marked area. Use: , Isopropanol
|
| | IMG-497926 |
|
| | |
| | IMG-498402 |
|
| | |
| | IMG-492660 |
|
| | Remove the protective film. |
| | IMG-498405 |
|
| | Install components that come with the accessory kit. |
| | IMG-491987 |
|
| | Use: 988734, Cable tie, 750 mm
|
| | IMG-492671 |
|
| | |
| | IMG-498410 |
|
| | |
| | IMG-498412 |
|
| | |
| | IMG-498483 |
|
| | Caution! Take extra care not to crease the headliner. |
Pull the wiring through. Remove the cable tie(s). |
| | IMG-498438 |
|
| | Position/route the cable as illustrated. Install the cable. Use: , Velcro strip
|
| | IMG-498479 |
|
| | Loosen the component indicated. Do not remove it. |
| | IMG-498436 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use: , Velcro strip
|
| | IMG-498496 |
|
| | Reinstall the removed part. To be repeated in the other end of the component. |
| | IMG-498497 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
Reinstall the removed part. To be repeated in the other end of the component. |
| | IMG-499420 |
|
| | |
| | IMG-499422 |
|
| | Remove the marking. Use: , Isopropanol
|
| | IMG-499434 |
|
| | Install component that comes with the accessory kit. |
| | IMG-499437 |
|
| | Caution! Take extra care not to crease the headliner. |
Route the wire adjacent to existing wirings. Use: , Velcro strip
|
| | IMG-497411 |
|
| | Install components that come with the accessory kit. Install the cable. |
| | IMG-498011 |
|
| | Caution! Take extra care not to crease the headliner. |
Position/route the cables as illustrated. Push in the wires. |
| | IMG-498164 |
|
| | Route the wire adjacent to existing wirings. assemble the cables. Use: , Velcro strip
|
| | IMG-498176 |
|
| | Position/route the cable as illustrated. Install the cable. Use: , Velcro strip
|
| | IMG-490780 |
|
| | |
| | IMG-490899 |
|
| | Remove the clip. Remove the marked part. |
| | IMG-490781 |
|
| | Remove the clips. Remove the marked part. |
| | IMG-498273 |
|
| | Position/route the cables as illustrated. |
| | IMG-497232 |
|
| | Assemble components that come with the accessory kit. |
| | IMG-498307 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use: , Velcro strip
|
| | IMG-490787 |
|
| | Release the lock. Remove the marked part. |
| | IMG-491242 |
|
| | |
| | IMG-498190 |
|
| | Install components that come with the accessory kit. |
| | IMG-498191 |
|
| | Caution! Make sure that no part of the wiring harness is trapped. |
|
| | IMG-498293 |
|
| | Reinstall the removed part. |
| | IMG-498299 |
|
| | Connect the ground cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-498302 |
|
| | Position the cable harness excess as illustrated. Install the cable. Use: , Velcro strip
|
| | IMG-498319 |
|
| | Position/route the cable as illustrated. |
| | IMG-498323 |
|
| | Position/route the cable as illustrated. Install the cable. Use: , Velcro strip
|
| | IMG-498334 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use: , Velcro strip
|
| | IMG-498471 |
|
| | Connect the connectors. Position the cable harness excess as illustrated. |
| | IMG-498472 |
|
| | Route the wire adjacent to existing wirings. Install the cables. Use: , Velcro strip
|
| | |
| | IMG-480454 |
|
| | Reinstall the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
| | IMG-497537 |
|
| | Download the app for the accessory according to the camera's manual Connect the app to the camera |
| | IMG-497545 |
|
| | Adjust the camera lens vertically so that the rear edge of the hood is visible at the bottom of the image in the app. Adjust the camera lens vertically so that the lower edge of the rear window is visible at the bottom of the image in the app.
|
| | |
| | IMG-498473 |
|
| | |
| | IMG-498474 |
|
| | Check for correct operation. |
| | Reinstall the removed parts in reverse order. |