| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | There may be parts in the accessories kit that are not needed for this installation. |
| | |
|  | | IMG-363036 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
|  | | IMG-497538 |
|
| | There may be parts in the accessories kit that are not needed for this installation. |
| | Disconnecting the battery |
|  | | IMG-480317 |
|
| | |
|  | | IMG-473637 |
|
| | |
|  | | IMG-473659 |
|
| | Remove the clips. Remove the marked part. |
|  | | IMG-473722 |
|
| | Remove the battery's negative cable. |
| | |
|  | | IMG-498376 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
|  | | IMG-498377 |
|
| | |
|  | | IMG-498378 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-498379 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
| | |
|  | | IMG-498450 |
|
| | Caution!
Make sure that the surface is clean and free of foreign material. |
Clean the marked area. Use: , Isopropanol
|
|  | | IMG-499117 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-499118 |
|
| | Lift approximately 2 mm. Remove the marked part.
|
|  | | IMG-499401 |
|
| | Note!
Do not remove the protective film. |
Place the component where indicated in the graphic. Measure |
|  | | IMG-499408 |
|
| | |
|  | | IMG-499410 |
|
| | |
|  | | IMG-499414 |
|
| | Apply a thin and even layer. Use: 1161823, Activator
|
|  | | IMG-499415 |
|
| | |
|  | | IMG-499105 |
|
| | Remove the protective film. |
|  | | IMG-499417 |
|
| | Note!
Press the component to remove any air bubbles between the window and the component. |
Allow to dry for at least 20 minutes. |
| | |
|  | | IMG-431485 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-431600 |
|
| | |
|  | | IMG-490420 |
|
| | |
|  | | IMG-491220 |
|
| | |
|  | | IMG-491223 |
|
| | Remove the screw.
Tightening torque: Panel A-pillar
, 4.5 Nm
|
|  | | IMG-491227 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-491237 |
|
| | |
| | |
|  | | IMG-499273 |
|
| | Caution!
Take extra care not to crease the headliner. |
Install component that comes with the accessory kit. Position/route the cable as illustrated. |
|  | | IMG-498164 |
|
| | Route the wire adjacent to existing wirings. assemble the cables. Use: , Velcro strip
|
|  | | IMG-498529 |
|
| | Position/route the cable as illustrated. Install the cable. |
|  | | IMG-490780 |
|
| | |
|  | | IMG-490899 |
|
| | Remove the clip. Remove the marked part. |
|  | | IMG-490781 |
|
| | Remove the clips. Remove the marked part. |
|  | | IMG-490787 |
|
| | Release the lock. Remove the marked part. |
|  | | IMG-497232 |
|
| | Assemble components that come with the accessory kit. |
|  | | IMG-498530 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use: , Velcro strip
|
|  | | IMG-491242 |
|
| | Remove fuses. The parts are not to be reused. |
|  | | IMG-498190 |
|
| | Install components that come with the accessory kit. |
|  | | IMG-498191 |
|
| | Caution!
Make sure that no part of the wiring harness is trapped. |
|
|  | | IMG-498293 |
|
| | Reinstall the removed part. |
|  | | IMG-498299 |
|
| | Connect the ground cable. Install the nut.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-498302 |
|
| | Position the cable harness excess as illustrated. Install the cable. Use: , Velcro strip
|
|  | | IMG-499420 |
|
| | |
|  | | IMG-499422 |
|
| | Remove the marking. Use: , Isopropanol
|
|  | | IMG-492443 |
|
| | Install component that comes with the accessory kit. Connect the connector. |
|  | | IMG-499434 |
|
| | |
|  | | IMG-499610 |
|
| | Caution!
Take extra care not to crease the headliner. |
Route the wire adjacent to existing wirings. Use: , Velcro strip
|
| | |
|  | | IMG-480454 |
|
| | Reinstall the battery's negative cable.
Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
|  | | IMG-492525 |
|
| | Download the app for the accessory according to the camera's manual Connect the app to the camera |
|  | | IMG-492531 |
|
| | Adjust the camera lens vertically so that the rear edge of the hood is visible at the bottom of the image in the app. |
| | |
| | Reinstall the removed parts in reverse order. |
