Installation Instructions

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2010
XC70 (08-) 2010

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307569841.331401809, 31401808, 31401804, 31401803, 31369837, 31369836, 31369841, 31369835, 31369834, 31369833, 30756617, 30756616, 30756613, 30756612, 30756611, 30756610
Steering wheel




IMG-326023




 
Equipment
A0000162
IMG-239664

D8802049

M8802108

IMG-326028

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-237320
 

  • Turn the ignition key to position I to release the steering wheel lock.

  • Disconnect the battery negative lead.


Note!

The SRS system remains active for a brief period after power is cut off. Thus, wait three minutes before starting work.


2
IMG-329033
 

  • Loosen the lever and pull the steering wheel console backwards.

  • Carefully prize off the rubber seal in the steering wheel cover all around.

  • 3
    IMG-329034
     

  • Carefully pull it off and remove the panel with the rubber seal.

  • 4
    IMG-328978
     

  • Carefully prize off the upper cover from the lower one at the rear. Remove the cover. It is fitted with clips at the sides.

  • 5
    IMG-217441
     

    • Turn the steering wheel a quarter turn so that the holes on the reverse of the steering wheel are accessible.

    6A
    IMG-328983
    6B
    IMG-328989
     

    Illustrations A and B

  • Use a screwdriver that is at least 5.2 mm wide and with a length of 200-250 mm.

  • 7A
    IMG-328990
    7B
    IMG-329000
    7C
    IMG-329001
    7D
    IMG-329002
     

    Illustration A

  • Insert a screwdriver into the large hole on the rear of the steering wheel's rear face.

  • Illustration B

  • Insert the tip of the screwdriver (1) under the lock spring (2).

  • Illustration C

  • Turn the screwdriver so that the end presses the lock spring up until it can move past the locking catch (3)

  • Illustration D

  • Carefully pull off one side of the steering wheel module. It is firmly attached.

  • Turn the steering wheel 180º.

  • Repeat for the lock spring on the other side.

  • Turn the steering wheel to neutral position.

  • 8
    IMG-329003
     

  • Carefully fold back the steering wheel module so that the connectors in the upper edge are accessible.

  • Press in the catches on the connectors (small illustration) and detach them.

  • Place the steering wheel module to one side


  • Caution!

    Position the steering wheel module with the front upwards in a secure position while carrying out the work.


  • 9
    IMG-329005
     

  • Grip the panel in the upper left-hand corner and carefully pull it loose until the pin releases. Use both hands.

  • Repeat the operation on the other side.

  • 10
    IMG-329006
     

  • Use a weatherstrip tool, turn and carefully pull the panel loose at the bottom on both sides. Put it to one side. There is a new component in the kit.

  • 11
    IMG-329007
     

  • Unplug the green connector in the contact reel.

  • Detach the ground cable from the bottom of the steering wheel.

  • Detach the cables to the keypads from their positions in the steering wheel.

  • 12
    IMG-329008
     

  • Remove the left and right-hand keypad/keypad dummy from the steering wheel by gently prizing them off with a plastic weatherstrip tool.

  • Turn the weatherstrip tool to press out the keypad. They are firmly attached with three pins in the steering wheel, so force is required to remove them.

  • 13
    IMG-329009
     

    Applies to cars with an RTI keypad

  • Unplug the connector (1) for the RTI keypad on the right keypad.

  • Remove the screw (2).

  • 14
    J6400900
     

  • Pry up the keypad at the front edge and unhook it from the steering wheel at the rear edge

  • Pull the cable out of the steering wheel.

  • 15
    IMG-329010
     

    Applies to all models

  • Loosen the screw in the steering wheel, but do not remove the screw.

  • Take the screw (1) and screw it in the bracket (2) in the contact reel.

  • Remove the screw and the steering wheel and put them to one side.

  • Take the new steering wheel and screw from the kit

  • 16
    J6400902
     

    Applies to cars with an RTI keypad

  • Remove the cover on the reverse of the right-hand spoke on the new steering wheel.

  • 17
    IMG-329011
     

    Applies to all models

  • Take the new steering wheel and align the guide pins in the contact reel in the holes in the steering wheel.

  • Take a new screw for the steering wheel and screw it in by hand.

  • Remove the screw in the bracket (1) in the contact reel and reinsert it in position (2).

  • Tighten and torque tighten the steering wheel screw.

  • 18
    IMG-329012
     

  • Grip the panel in the upper left-hand corner and carefully pull it loose until the pin releases. Use both your hands.

  • Repeat the operation on the other side.

  • 19
    IMG-329013
     

  • Use a weatherstrip tool, turn and carefully pull the panel loose at the bottom on both sides.

  • 20A
    IMG-329188
    20B
    IMG-329014
     

    Applies to cars with an RTI keypad

    Illustrations A and B

  • Insert the cables for the RTI keypad on the back of the steering wheel and pull them forward.

  • Reinstall the keypad on the reverse of the steering wheel. Tighten using the screw (1).

  • Plug in the connector (2) for the steering wheel's right-hand keypad.

  • 21
    IMG-329016
     

    Applies to all models

  • Refit the keypads.

  • Fit the cables in their grooves.

  • Plug in the green connector in the contact reel.

  • Tighten the ground cable.

  • 22
    IMG-329018
     

  • Take the panel and firmly press into the steering wheel.

  • 23
    IMG-329019
     

  • Take the steering wheel module and check that the three spring-loaded holders are firmly attached to it. If any holder has become trapped in the bottom of the steering wheel, remove it and fit it on the steering wheel module.

  • 24
    IMG-329020
     

  • Plug in the two connectors for the steering wheel module.

  • Position the steering wheel module in the centre of the steering wheel and press it firmly into bottom of the steering wheel.

  • Check that it is fitted firmly and can be pressed in all around.

  • 25
    IMG-329021
     

    26
    IMG-329022
     

    27
    IMG-329023
     

    28
    IMG-236182
     

    Installing the negative lead after working with SRS components


  • Warning!

    Make sure that no one is in the vehicle during this procedure.


  • Activate the SRS system in accordance with: "VIDA/ DIAGNOSTICS/ VEHICLE COMMUNICATION/ Advanced/ SRS/ Powering the SRS system" before turning the ignition key.

  • Initiate window position in accordance with: "VIDA/ DIAGNOSTICS/ VEHICLE COMMUNICATION/ Advanced/ Initiating window position"