Navigation system, portable - V50 2005 T5 AWD Manual - Volvo Cars Tilbehør

2005 T5 AWD MANUAL L.H.D

V50 Biler

Monteringsveiledning

Installation instructions, accessories

Volvo Car Corporation Gothenburg, Sweden

V50 2005

Instruction No		Version		Part. No.
31330966		1.1		31330863, 31330864, 31330865, 31330866, 31330867, 31330868, 9487194, 9487195, 9487196

Navigation system, portable

IMG-350807

Special tools

951 2932 Tension spring

Tool number:951 2932

Tool description:Tension spring

Tool boards:80

Equipment

A0000162

IMG-239660

IMG-239681

IMG-317443

IMG-327738

IMG-244945

IMG-239981

IMG-239667

IMG-239664

IMG-347417

Information

1

Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available before starting installation.
Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Conditions

2

Where the procedure differs, the right-hand version is also shown with text and image.

3

IMG-332193

Set the ignition key to position 0.

Removal

4

IMG-350274

Remove the panel.

5

IMG-353198

Remove the clip.

6

IMG-353200

7

IMG-350312

8

IMG-350313

Remove the panel.

9

IMG-353196

Remove the screw.

10

IMG-353197

Remove the screws.

11

IMG-353218

Remove the panel.

12

IMG-353212

13

IMG-353217

Disconnect the connectors.

14

IMG-350268

Detach the panel.

15

IMG-353276

Unhook the clip(s).

16

IMG-350837

17

IMG-350841

Measure and mark as illustrated.

18

IMG-351371

19

IMG-347549

20

IMG-350046

Center the holes against each other.

21

IMG-347339

Note!
Ensure that the part is correctly positioned against the panel's surface.

Drill the holes.

22

IMG-346740

Install the screws.

23

IMG-348746

24

IMG-346732

Remove the screws.

25

IMG-347714

Adjust the cable length so that the marking ends up as displayed in the image.

Right-hand drive vehicles

26

IMG-348302

Adjust the cable length so that the marking ends up as displayed in the image.

All vehicles

27

IMG-350293

Install the screws.

28

IMG-353171

Fold the insulation to one side.

29

IMG-350631

30

IMG-350629

Use special tool: T9512932, Tension spring

Pull the wiring through.

31

IMG-353301

32

IMG-353297

33

IMG-353302

Install the panel.

34

IMG-350877

35

IMG-223767

Remove the panel.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

36

IMG-350878

37

IMG-350881

Remove the panel.

38

IMG-350882

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

39

IMG-350876

40

IMG-350282

41

IMG-350511

Fold the carpet to the side.

42

IMG-350827

Remove the panel.

43

IMG-350962

Disconnect the connector.

44

IMG-350934

Use special tool: T9512932, Tension spring

45

IMG-350946

Pull the wiring through.

46

IMG-350616

47

IMG-350933

Connect the connectors.

48

IMG-350932

Tear off the excess foam tape.

49

IMG-350951

50

IMG-350956

51

IMG-350617

Route the cable harness to the existing cable harness.

52

IMG-353237

53

IMG-353235

Place any excess inside the floor carpet.

54

IMG-353238

Fold the floor carpet back.

55

IMG-353243

Connect the connectors.

56

IMG-353248

Tear off the excess foam tape.

57

IMG-353250

Reinstall the removed parts in reverse order.

58

IMG-350831