Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

These installation instructions show installation on left hand drive cars.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Where the procedure differs, the right-hand version is also shown with text and image.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Accessory installation

Measure and mark as illustrated.

Removal

Set the ignition key to position 0.

Remove the screw.

Tightening torque: Panel A-pillar , 3 Nm

Remove the panel.

Remove the screws.

Tightening torque: M6 , 10 Nm

Repeat the steps when removing on opposite side.

Remove the weatherstrips.

Detach the panel.

Remove the panel.

Remove the screws.

Tightening torque: M6 , 10 Nm

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Disconnect the connector.

Disconnect the connector.

Fold the carpet aside.

Accessory installation

Use special tool: T9814116, Cylindrical knife

Install the catch.

Turn once.

Tear off the excess foam tape.

Adjust the position of the wiring harness.

Installation

Repeat the steps when installing on opposite side.

Install the cable.

Removal

Disconnect the connector.

Remove the screws.

Cars with automatic transmissions

Release the shift-lock function.

All vehicles

Remove the part carefully

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Vehicles with DVD-player

Disconnect the connector.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

All vehicles

Disconnect the connectors.

Remove the screws.

Use hands only.

Use hands only.

Disconnect the connectors.

Remove the screws.

Disconnect the connector.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

Disconnect the connectors.

Accessory installation

Locate the connector.

Connect the cable harness.

Turn once.

Tear off the excess foam tape.

Locate the connector.

Connect the cable harness.

Turn once.

Tear off the excess foam tape.

Use special tool: T9814089, Anti-static strap

Tighten the cable tie.

Installation

Connect the prerouted cable.

Connect the connectors.

Reinstall the screws.

Connect the connectors.

Reinstall the removed part.

Remove the tool.

Vehicles with DVD-player

Connect the prerouted cable.

Vehicles without DVD-player

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

All vehicles

Connect the connectors.

Accessory installation

Clean the surface.

Use: , Isopropanol

Remove the protective film.

Remove the screws.

Measure and mark as illustrated.

Deburr the hole edges.

Reinstall the screws.

Connect the connectors.

Connect the connector.

Connect the connector.

Reinstall the removed part.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31399196

Place the manual for this accessory in a suitable location in the car.

Check

1. Turn on the ignition.

2. Press the button marked "Media".

3. Choose Sensus Connected Touch in the menu.

4. Reply YES to the question "DO YOU ALLOW THE GPS POSITIONING DATA TO BE USED?"

5. The Sensus Connected Touch start menu should show.

6. Move your finger from right to left over the display. Start from the inner edge of the display.

7. A new menu should now show.

8. Turn off the ignition.

System check

Follow the instructions on www.volvocars.com/sct-update and check if the system is equipped with the latest software. If not, follow the instructions to carry out update.

Applies when the customer has chosen map information for navigation

Removal

Does not apply to vehicles for the Chinese market.

The part is not to be reused.

Applies to all markets.

Accessory installation