Sill molding - XC60 2012 - Volvo Cars Accessories Web

Installation instructions, accessories

Volvo Car Corporation Gothenburg, Sweden

XC60 2012

Instruction No		Version		Part. No.
31373895		1.3		30721133

Sill molding

IMG-266944

Equipment

IMG-345497

IMG-333288

IMG-333293

IMG-332313

IMG-289864

INTRODUCTION

Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available before starting installation.
Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Front door

IMG-297967

Front door

Wash the door sill

IMG-297968

Place a strip of tape in the front edge of the sill panel, square to the edge of the door sill.

IMG-323263

Measure out a distance of 40 mm (1 9/16") from the front of the tape strip and forward, to mark the sill moulding's front position. Fasten a tape strip as shown in the image.

IMG-323264

Remove the rear strip of tape.

IMG-290343

Position the sill moulding by the strip of tape on the front edge. Position it so that the cut-outs at both ends align with the corresponding door sill. Exercise care when positioning so the that moulding is not misaligned.
Attach a strip of tape to mark the sideways position.

IMG-290344

Clean the marked surface on the sill using isopropanol and wipe dry.

IMG-290345

Peal back the ends on the front edge of the two long fastening tapes.
Remove the protective tape on the two short fastening tapes.

IMG-290346

Position the sill moulding by the strips of tape on the front edge and the two strips of tape at the sides. Press down the ends firmly. Exercise care when positioning so the that moulding is not misaligned.

IMG-290347

Carefully pull away the protective tape and successively push down into position, first the outer and then the inner tape. Make sure the rubber moulding is not in the way.

Note!

Do not push down the strip too close to the protective tape on the inner tape. The strip lies close to the sill and can catch here whereby the tape can break.

IMG-290348

Press the sill moulding down firmly with a pressure of approximately 2 kg/cm² along its entire length.
Remove the tape markings.
Repeat the operation on the other side.

Rear door

IMG-297874

Rear door

Wash the door sill

IMG-290349

Place a strip of tape on the front edge of the sill panel and square to the edge of the door sill.

IMG-290350

Position the sill moulding by the strip of tape on the front edge and position it so that the cut-outs at both ends align with the corresponding door sill. Exercise care when positioning so the that moulding is not misaligned.
Attach a strip of tape to mark the sideways position.

IMG-290351

Clean the marked surface on the sill using isopropanol and wipe dry.

IMG-300145

Remove all the pieces of tape from the sill moulding.

IMG-290403

Align the moulding with the tape markings and carefully fold it down against the sill and push into position. Watch out for the sill's rubber moulding.
Remove the tape markings.

IMG-290404

Now press the entire strip so that it adheres properly.
Press the sill moulding down firmly with a pressure of approximately 2 kg/cm² along its entire length.
Repeat the operation on the other side.

Model year*
Engine
Transmission
Steering
Reset	Apply

Model year*
Engine
Transmission
Steering
Reset	Apply

Model year*
Engine
Transmission
Steering
Reset	Apply

Model year*
Engine
Transmission
Steering
Reset	Apply

Model year*
Engine
Transmission
Steering
Reset	Apply

Wish list is empty